The ADC10D1000/1500 is the latest advance in TI's Ultra-High-Speed ADC family. This low-power, high-performance CMOS analog-to-digital converter digitizes signals at 10-bit resolution for dual channels at sampling rates of up to 1.0/1.5 GSPS (Non-DES Mode) or for a single channel up to 2.0/3.0 GSPS (DES Mode). The ADC10D1000/1500 achieves excellent accuracy and dynamic performance while dissipating less than 2.8/3.6 Watts. The product is packaged in a leaded or lead-free 292-ball thermally enhanced BGA package over the rated industrial temperature range of -40°C to +85°C.

The ADC10D1000/1500 builds upon the features, architecture and functionality of the 8-bit GHz family of ADCs. An expanded feature set includes AutoSync for multi-chip synchronization, 15-bit programmable gain and 12-bit plus sign programmable offset adjustment for each channel. The improved internal track-and-hold amplifier and the extended self-calibration scheme enable a very flat response of all dynamic parameters beyond Nyquist, producing 9.1/9.0 Effective Number of Bits (ENOB) with a 100 MHz input signal and a 1.0/1.5 GHz sample rate while providing a 10^-18 Code Error Rate (CER) Dissipating a typical 2.77/3.59 Watts in Non-Demultiplex Mode at 1.0/1.5 GSPS from a single 1.9V supply, this device is specified to have no missing codes over the full operating temperature range.

Each channel has its own independent DDR Data Clock, DCLKI and DCLKQ, which are in phase when both channels are powered up, so that only one Data Clock could be used to capture all data, which is sent out at the same rate as the input sample clock. If the 1:2 Demux Mode is selected, a second 10-bit LVDS bus becomes active for each channel, such that the output data rate is sent out two times slower to relax data-capture timing requirements. The part can also be used as a single 2.0/3.0 GSPS ADC to sample one of the I or Q inputs. The output formatting can be programmed to be offset binary or two's complement and the Low Voltage Differential Signaling (LVDS) digital outputs are compatible with IEEE 1596.3-1996, with the exception of an adjustable common mode voltage between 0.8V and 1.2V to allow for power reduction for well-controlled back planes.

• Excellent Accuracy and Dynamic Performance
• Pin Compatible with ADC12D1000/1600/1800
• Low Power Consumption, Further Reduced at Lower Fs
• Internally Terminated, Buffered, Differential Analog Inputs
• R/W SPI Interface for Extended Control Mode
• Dual-Edge Sampling Mode, in Which the I- and Q-channels Sample One Input at Twice the Sampling Clock Rate
• Test Patterns at Output for System Debug
• Programmable 15-bit Gain and 12-bit Plus Sign Offset
• Programmable tAD Adjust Feature
• 1:1 Non-demuxed or 1:2 Demuxed LVDS Outputs
• AutoSync Feature for Multi-Chip Systems
• Single 1.9V ± 0.1V Power Supply
• 292-Ball BGA Package (27mm x 27mm x 2.4mm with 1.27mm Ball-Pitch); No Heat Sink Required

All trademarks are the property of their respective owners.

• Sample rate (Max) (MSPS)
• 1500, 3000
• Resolution (Bits)
• 10
• Number of input channels
• 2, 1
• Interface type
• Parallel LVDS
• Analog input BW (MHz)
• 2800
• Features
• Ultra High Speed
• Rating
• Catalog
• Input range (Vp-p)
• 0.8
• Power consumption (Typ) (mW)
• 3140
• Architecture
• Folding Interpolating
• SNR (dB)
• 57
• ENOB (Bits)
• 9.1
• SFDR (dB)
• 70
• Operating temperature range (C)
• -40 to 85
• Input buffer
• Yes

ADC10D1500的完整型号有：ADC10D1500CIUT、ADC10D1500CIUT/NOPB，以下是这些产品的关键参数及官网采购报价：

ADC10D1500CIUT，工作温度：-40 to 85，封装：BGA (NXA)-292，包装数量MPQ：40个，MSL 等级/回流焊峰值温度：Level-3-220C-168 HR，引脚镀层/焊球材料：SNPB，TI官网ADC10D1500CIUT的批量USD价格：2158.002（1000+）

ADC10D1500CIUT/NOPB，工作温度：-40 to 85，封装：BGA (NXA)-292，包装数量MPQ：40个，MSL 等级/回流焊峰值温度：Level-3-250C-168 HR，引脚镀层/焊球材料：SNAG，TI官网ADC10D1500CIUT/NOPB的批量USD价格：1598.52（1000+）

ADC-LD-BB — ADC 低失真不平衡变压器板

One ADC-LD-BBboard is included in the hardware kit with the GSPS analog-to-digital converter (ADC) reference boards. Since the analog inputs to the ADC1xDxx00RB are differential and most signal sources are single ended, these balun boards are generally used to achieve (...)

ADC-WB-BB — ADC 宽带不平衡变压器板

OneADC-WB-BB board is included in the hardware kit with the GSPS analog-to-digital converter (ADC) reference boards. Since the analog inputs to the ADC1xDxx00RB are differential and most signal sources are single ended, these balun boards are generally used to achieve (...)

ADC10D1500RB — ADC10D1500 是低功耗、10 位、双路 1.5 GSPS 或单路 3.0 GSPS AD 转换器参考板

The ADC10D1500 is the latest advance in Nationals Ultra-High-Speed ADC family. This low-power, high-performance CMOS analog-to-digital converter digitizes signals at 10-bit resolution for dual channels at sampling rates of up to 1.5 GSPS (Non-DES Mode) or for a single channel up to 3.0 GSPS (DES (...)

WAVEVISION5 — Data Acquisition and Analysis Software

WaveVision 5 software is part of the WaveVision evaluation system that also includes WaveVision 5 Data Capture Board. The WaveVision 5 system is an easy-to-use data acquisition and analysis tool, designed to help users evaluate Texas Instruments' Signal Path solutions.

While WaveVision 5 software (...)

PSPICE-FOR-TI — 适用于 TI 设计和模拟工具的 PSpice

PSpice for TI 可提供帮助评估模拟电路功能的设计和仿真环境。此功能齐全的设计和仿真套件使用 Cadence 的模拟分析引擎。PSpice for TI 可免费使用，包括业内超大的模型库之一，涵盖我们的模拟和电源产品系列以及精选的模拟行为模型。

借助?PSpice for TI 的设计和仿真环境及其内置的模型库，您可对复杂的混合信号设计进行仿真。创建完整的终端设备设计和原型解决方案，然后再进行布局和制造，可缩短产品上市时间并降低开发成本。

在?PSpice for TI 设计和仿真工具中，您可以搜索 TI (...)

TIDA-00113 — 在单通道模式或双通道模式下针对高带宽应用驱动 GSPS ADC

该设计旨在帮助系统设计人员权衡利弊，推动具有每秒千兆取样率的 ADC（采用平衡-非平衡变压器配置）在带宽应用中的应用，并对该实施过程进行优化。需考虑的权衡因素包括平衡-非平衡变压器的结构、插入损耗、动态性能、可配置性和实施的简便性。拓扑和布局在优化系统性能的过程中尤为重要，这也正是这些设计能够有助于缩短设计周期的原因所在。