The ADS1601 is a high-speed, high-precision, delta-sigma analog-to-digital converter (ADC) manufactured on an advanced CMOS process. The ADS1601 oversampling topology reduces clock jitter sensitivity during the sampling of high-frequency, large amplitude signals by a factor of four over that achieved by Nyquist-rate ADCs. Consequently, signal-to-noise ratio (SNR) is particularly improved. Total harmonic distortion (THD) is –103dB, and the spurious-free dynamic range (SFDR) is 105dB

Optimized for power and performance, the ADS1601 dissipates only 330mW while providing a full-scale differential input range of ±0.94V_REF. Having such a wide input range makes out-of-range signals uncommon. The OTR pin indicates if an analog input out-of-range condition does occur. The differential input signal is measured against the differential reference, which can be generated internally on the ADS1601 or supplied externally.

The ADS1601 uses an inherently stable advanced modulator with an on-chip decimation filter. The filter stop band extends to 19.3MHz, which greatly simplifies the anti-aliasing circuitry. The modulator samples the input signal up to 20MSPS, depending on f_CLK, while the 16x decimation filter uses a series of four half-band FIR filter stages to provide 75dB of stop band attenuation and 0.001dB of passband ripple.

Output data is provided over a simple 3-wire serial interface at rates up to 1.25MSPS, with a –3dB bandwidth of 615kHz. The output data or its complementary format directly connects to DSPs such as TI’s TMS320 family, FPGAs, or ASICs. A dedicated synchronization pin enables simultaneous sampling with multiple ADS1601s in multi-channel systems. Power dissipation is set by an external resistor that allows a reduction in dissipation when operating at slower speeds. All of the ADS1601 features are controlled by dedicated I/O pins, which simplify operation by eliminating the need for on-chip registers.

The high performing, easy-to-use ADS1601 is especially suitable for demanding measurement applications in sonar, vibration analysis, and data acquisition. The ADS1601 is offered in a small, 7mm × 7mm TQFP-48 package and is specified from –40°C to +85°C.

• High Speed:
  • Data Rate: 1.25MSPS
  • Bandwidth: 615kHz
• Outstanding Performance:
  • SNR: 92dB at fIN = 100kHz, –1dBFS
  • THD: –103dB at fIN = 100kHz, –6dBFS
  • SFDR: 105dB at fIN = 100kHz, –6dBFS
• Ease-of-Use:
  • High-Speed 3-Wire Serial Interface
  • Directly Connects to TMS320 DSPs
  • On-Chip Digital Filter Simplifies Anti-Alias Requirements
  • Simple Pin-Driven Control—No On-Chip Registers to Program
  • Selectable On-Chip Voltage Reference
  • Simultaneous Sampling with Multiple ADS1601s
• Low Power:
  • 330mW at 1.25MSPS
  • 145mW at 625kSPS
  • Power-Down Mode

• Resolution (Bits)
• 16
• Number of input channels
• 1
• Sample rate (Max) (kSPS)
• 1250
• Interface type
• Serial
• Architecture
• Delta-Sigma
• Input type
• Differential
• Multi-channel configuration
• —
• Rating
• Catalog
• Reference mode
• Ext, Int
• Input range (Max) (V)
• 4.6
• Input range (Min) (V)
• 0
• Features
• —
• Operating temperature range (C)
• -40 to 85
• Power consumption (Typ) (mW)
• 330
• Analog voltage AVDD (Min) (V)
• 4.75
• SNR (dB)
• 91
• Analog voltage AVDD (Max) (V)
• 5.25
• INL (Max) (+/-LSB)
• 0.75
• Digital supply (Min) (V)
• 2.7
• Digital supply (Max) (V)
• 5.25

ADS1601的完整型号有：ADS1601IPFBR、ADS1601IPFBT，以下是这些产品的关键参数及官网采购报价：

ADS1601IPFBR，工作温度：-40 to 85，封装：TQFP (PFB)-48，包装数量MPQ：1000个，MSL 等级/回流焊峰值温度：Level-2-260C-1 YEAR，引脚镀层/焊球材料：NIPDAU，TI官网ADS1601IPFBR的批量USD价格：7.818（1000+）

ADS1601IPFBT，工作温度：-40 to 85，封装：TQFP (PFB)-48，包装数量MPQ：250个，MSL 等级/回流焊峰值温度：Level-2-260C-1 YEAR，引脚镀层/焊球材料：NIPDAU，TI官网ADS1601IPFBT的批量USD价格：9.308（1000+）

ADS1601 IBIS Model (Rev. A)

PSpice for TI 可提供帮助评估模拟电路功能的设计和仿真环境。此功能齐全的设计和仿真套件使用 Cadence 的模拟分析引擎。PSpice for TI 可免费使用，包括业内超大的模型库之一，涵盖我们的模拟和电源产品系列以及精选的模拟行为模型。

借助?PSpice for TI 的设计和仿真环境及其内置的模型库，您可对复杂的混合信号设计进行仿真。创建完整的终端设备设计和原型解决方案，然后再进行布局和制造，可缩短产品上市时间并降低开发成本。

在?PSpice for TI 设计和仿真工具中，您可以搜索 TI (...)

TINA-TI — 基于 SPICE 的模拟仿真程序

TINA-TI 提供了 SPICE 所有的传统直流、瞬态和频域分析以及更多。TINA 具有广泛的后处理功能，允许您按照希望的方式设置结果的格式。虚拟仪器允许您选择输入波形、探针电路节点电压和波形。TINA 的原理图捕获非常直观 - 真正的“快速入门”。

TINA-TI 安装需要大约 500MB。直接安装，如果想卸载也很容易。我们相信您肯定会爱不释手。

TINA 是德州仪器 (TI) 专有的 DesignSoft 产品。该免费版本具有完整的功能，但不支持完整版 TINA 所提供的某些其他功能。

如需获取可用 TINA-TI 模型的完整列表，请参阅：SpiceRack - 完整列表

需要 HSpice (...)

ADC-INPUT-CALC — Analog-to-digital converter (ADC) input driver design tool supporting multiple input types

ADC-INPUT-CALC 是一种在线工具，可为设计模数转换器 (ADC) 的输入缓冲器提供支持。它提供 24 种不同的基于运算放大器的缓冲器电路，这些电路可用于驱动 ADC 输入。可用拓扑涵盖差分单端和变压器耦合输入设计。支持交流耦合和直流耦合设计以及单电源和双电源拓扑。提供两种模式：初学者模式和专家模式。在初学者模式中，设计人员先回答一系列问题，然后会看到解决方案原理图，在某些情况下，还会看到解决方案的可选版本。在专家模式下，设计人员会看到用方框图形式显示的所有 24 (...)

ANALOG-ENGINEER-CALC — 模拟工程师计算器

模拟工程师计算器旨在加快模拟电路设计工程师经常使用的许多重复性计算。该基于 PC 的工具提供图形界面，其中显示各种常见计算的列表（从使用反馈电阻器设置运算放大器增益到为稳定模数转换器 (ADC) 驱动器缓冲器电路选择合适的电路设计元件）。除了可用作单独的工具之外，该计算器还能够很好地与模拟工程师口袋参考书中所述的概念配合使用。 lock = 需要出口许可（1分钟）