The AM26LV32E consists of quadruple differential line receivers with 3-state outputs. These differential receivers have ±15-kV ESD (HBM and IEC61000-4-2, Air-Gap Discharge) and ±8-kV ESD (IEC61000-4-2, Contact Discharge) protection for RS422 bus pins.

This device is designed to meet TIA/EIA-422-B and ITU recommendation V.11 drivers with reduced supply voltage. The device is optimized for balanced bus transmission at switching rates up to 32 MHz. The 3-state outputs permit connection directly to a bus-organized system.

The AM26LV32E has an internal fail-safe circuitry that prevents the device from putting an unknown voltage signal at the receiver outputs. In the open fail-safe, shorted fail-safe, and terminated fail-safe, a high state is produced at the respective output.

This device is supported for partial-power-down applications using I_off. I_off circuitry disables the outputs, preventing damaging current backflow through the device when it is powered down.

The AM26LV32EM is characterized for operation from –55°C to 125°C.

• Meets or Exceeds Standard TIA/EIA-422-B and ITU Recommendation V.11
• Operates From a Single 3.3-V Power Supply
• ESD Protection for RS422 Bus Pins
  • ±15-kV Human-Body Model (HBM)
  • ±8-kV IEC61000-4-2, Contact Discharge
  • ±15-kV IEC61000-4-2, Air-Gap Discharge
• Switching Rates up to 32 MHz
• Low Power Dissipation: 27 mW Typ
• Open-Circuit, Short-Circuit, and Terminated Fail-Safe
• ±7-V Common-Mode Input Voltage Range With ±200-mV Sensitivity
• Accepts 5-V Logic Inputs With 3.3-V Supply (Enable Inputs)
• Input Hysteresis: 35 mV Typ
• Pin-to-Pin Compatible With AM26C32, AM26LS32
• Ioff Supports Partial-Power-Down Mode Operation

(1) Additional temperature ranges are available – contact factory

• Number of receivers
• 4
• Number of transmitters
• 0
• Duplex
• Half
• Supply voltage (Nom) (V)
• 3.3
• Signaling rate (Max) (Mbps)
• 32
• IEC 61000-4-2 contact (+/- kV)
• 8
• Fault protection (V)
• -14 to 14
• Common mode range
• -7 to 7
• Number of nodes
• 32
• Features
• IEC ESD protection
• Isolated
• No
• ICC (Max) (mA)
• 17
• Rating
• HiRel Enhanced Product
• Operating temperature range (C)
• -55 to 125

AM26LV32E-EP的完整型号有：AM26LV32EMDREP、V62/09602-01XE，以下是这些产品的关键参数及官网采购报价：

AM26LV32EMDREP，工作温度：-55 to 125，封装：SOIC (D)-16，包装数量MPQ：2500个，MSL 等级/回流焊峰值温度：Level-1-260C-UNLIM，引脚镀层/焊球材料：NIPDAU，TI官网AM26LV32EMDREP的批量USD价格：2.393（1000+）

V62/09602-01XE，工作温度：-55 to 125，封装：SOIC (D)-16，包装数量MPQ：2500个，MSL 等级/回流焊峰值温度：Level-1-260C-UNLIM，引脚镀层/焊球材料：NIPDAU，TI官网V62/09602-01XE的批量USD价格：2.393（1000+）

AM26LV32E IBIS Model (Rev. A)

PSpice for TI 可提供帮助评估模拟电路功能的设计和仿真环境。此功能齐全的设计和仿真套件使用 Cadence 的模拟分析引擎。PSpice for TI 可免费使用，包括业内超大的模型库之一，涵盖我们的模拟和电源产品系列以及精选的模拟行为模型。

借助?PSpice for TI 的设计和仿真环境及其内置的模型库，您可对复杂的混合信号设计进行仿真。创建完整的终端设备设计和原型解决方案，然后再进行布局和制造，可缩短产品上市时间并降低开发成本。

在?PSpice for TI 设计和仿真工具中，您可以搜索 TI (...)

TINA-TI — 基于 SPICE 的模拟仿真程序

TINA-TI 提供了 SPICE 所有的传统直流、瞬态和频域分析以及更多。TINA 具有广泛的后处理功能，允许您按照希望的方式设置结果的格式。虚拟仪器允许您选择输入波形、探针电路节点电压和波形。TINA 的原理图捕获非常直观 - 真正的“快速入门”。

TINA-TI 安装需要大约 500MB。直接安装，如果想卸载也很容易。我们相信您肯定会爱不释手。

TINA 是德州仪器 (TI) 专有的 DesignSoft 产品。该免费版本具有完整的功能，但不支持完整版 TINA 所提供的某些其他功能。

如需获取可用 TINA-TI 模型的完整列表，请参阅：SpiceRack - 完整列表

需要 HSpice (...)