- 制造厂商：TI
- 产品类别：电源管理
- 技术类目：电池管理 IC - 电池电量监测
- 功能描述：具有单总线 (DQ) 接口和 5 个 LED 驱动器的镍镉电池/镍氢电池电量监测计
- 点击这里打开及下载BQ2010的技术文档资料
- TI代理渠道，提供当日发货、严格的质量标准，满足您的目标价格
The bq2010 Gas Gauge IC is intended for battery-pack or in-system installation to maintain an accurate record of a battery’s available charge. The IC monitors a voltage drop across a sense resistor connected in series between the negative battery terminal and ground to determine charge and discharge activity of the battery.
NiMH and NiCd battery self-discharge is estimated based on an internal timer and temperature sensor. Compensations for battery temperature and rate of charge or discharge are applied to the charge, discharge, and self-discharge calculations to provide available charge information across a wide range of operating conditions. Battery capacity is automatically recalibrated, or "learned," in the course of a discharge cycle from full to empty.
Nominal available charge may be directly indicated using a five- or six-segment LED display. These segments are used to indicate graphically the nominal available charge.
The bq2010 supports a simple single-line bidirectional serial link to an external processor (common ground). The bq2010 outputs battery information in response to external commands over the serial link.
The bq2010 may operate directly from 3 or 4 cells. With the REF output and an external transistor, a simple, inexpensive regulator can be built to provide VCC across a greater number of cells.
Internal registers include available charge, temperature, capacity, battery ID, battery status, and programming pin settings. To support subassembly testing, the outputs may also be controlled. The external processor may also overwrite some of the bq2010 gas gauge data registers.
- Conservative and repeatable measurement of available charge in rechargeable batteries
- Designed for battery pack integration
- 120μA typical standby current
- Small size enables implementations in as little as ? square inch of PCB
- Integrate within a system or as a stand-alone device
- Display capacity via single-wire serial communication port or direct drive of LEDs
- Measurements compensated for current and temperature
- Self-discharge compensation using internal temperature sensor
- Accurate measurements across a wide range of current (> 500:1)
- 16-pin narrow SOIC
- Cell chemistry
- NiCd, NiMH
- Number of series cells
- 2-4 Cells
- Communication interface
- DQ
- Battery capacity (Min) (mAh)
- 500
- Battery capacity (Max) (mAh)
- 6000
- Implementation
- Pack
- External capacity indication
- LED
- Features
- Coulomb Counter
- Operating temperature range (C)
- 0 to 70
- Cell balancing
- —
BQ2010的完整型号有：BQ2010SN-D107、BQ2010SN-D107TR，以下是这些产品的关键参数及官网采购报价：
BQ2010SN-D107，工作温度：0 to 70，封装：SOIC (D)-16，包装数量MPQ：40个，MSL 等级/回流焊峰值温度：Level-2-260C-1 YEAR，引脚镀层/焊球材料：NIPDAU，TI官网BQ2010SN-D107的批量USD价格：10.356（1000+）
BQ2010SN-D107TR，工作温度：0 to 70，封装：SOIC (D)-16，包装数量MPQ：2500个，MSL 等级/回流焊峰值温度：Level-2-260C-1 YEAR，引脚镀层/焊球材料：NIPDAU，TI官网BQ2010SN-D107TR的批量USD价格：8.928（1000+）
BQ2010SN-D107，工作温度：0 to 70，封装：SOIC (D)-16，包装数量MPQ：40个，MSL 等级/回流焊峰值温度：Level-2-260C-1 YEAR，引脚镀层/焊球材料：NIPDAU，TI官网BQ2010SN-D107的批量USD价格：10.356（1000+）
BQ2010SN-D107TR，工作温度：0 to 70，封装：SOIC (D)-16，包装数量MPQ：2500个，MSL 等级/回流焊峰值温度：Level-2-260C-1 YEAR，引脚镀层/焊球材料：NIPDAU，TI官网BQ2010SN-D107TR的批量USD价格：8.928（1000+）
