The bq2060A SBS-compliant gas gauge IC for battery pack or in-system installation maintains an accurate record of available charge in rechargeable batteries. The bq2060A monitors capacity and other critical battery parameters for NiCd, NiMH, Li-ion, and lead-acid chemistries. The bq2060A uses a voltage-to-frequency converter with automatic offset error correction for charge and discharge counting. For voltage, temperature, and current reporting, the bq2060A uses an A-to-D converter. The onboard ADC also monitors individual cell voltages in a Li-ion battery pack and allows the bq2060A to generate control signals that may be used with a pack supervisor to enhance pack safety.

The bq2060A supports the smart battery data (SBData) commands and charge-control functions. It communicates data using the system management bus (SMBus) 2-wire protocol or the Benchmarq 1-wire HDQ16 protocol. The data available include the remaining battery capacity, temperature, voltage, current, and remaining run-time predictions. The bq2060A provides LED drivers and a pushbutton input to depict remaining battery capacity from full to empty in 20% or 25% increments with a 4- or 5-segment display.

The bq2060A works with an external EEPROM. The EEPROM stores the configuration information for the bq2060A, such as battery chemistry, self-discharge rate, rate compensation factors, measurement calibration, and design voltage and capacity. The bq2060A uses the programmable self-discharge rate and other compensation factors stored in the EEPROM to accurately adjust remaining capacity for use and standby conditions based on time, rate, and temperature. The bq2060A also automatically calibrates or learns the true battery capacity in the course of a discharge cycle from near-full to near-empty levels.

The REG output regulates the operating voltage for the bq2060A from the battery cell stack using an external JFET.

• Provides Accurate Measurement of Available Charge in NiCd, NiMH, Li-Ion, and Lead-Acid Batteries
• Supports SBS Smart Battery Data Specification v1.1
• Supports the 2-Wire SMBus v1.1 Interface With PEC or 1-Wire HDQ16
• Reports Individual Cell Voltages
• Monitors and Provides Control to Charge and Discharge FETs in Li-Ion Protection Circuit
• Provides 15-Bit Resolution for Voltage, Temperature, and Current Measurements
• Measures Charge Flow Using a V-to-F Converter With Offset of Less Than 16 μV After Calibration
• Consumes Less Than 0.5 mW Operating
• Drives a 4- or 5-Segment LED Display for Remaining Capacity Indication
• 28-Pin 150-Mil (3,8-mm) SSOP

• Cell chemistry
• Lead Acid, Li-Ion/Li-Polymer, NiCd, NiMH
• Number of series cells
• 2-4 Cells
• Communication interface
• HDQ, SMBus
• Battery capacity (Min) (mAh)
• 800
• Battery capacity (Max) (mAh)
• 10000
• Implementation
• Pack
• External capacity indication
• LED
• Features
• Coulomb Counter
• Operating temperature range (C)
• -20 to 70
• Cell balancing
• —

BQ2060A的完整型号有：BQ2060A-E619DBQ、BQ2060A-E619DBQR，以下是这些产品的关键参数及官网采购报价：

BQ2060A-E619DBQ，工作温度：-20 to 70，封装：SSOP (DBQ)-28，包装数量MPQ：40个，MSL 等级/回流焊峰值温度：Level-2-260C-1 YEAR，引脚镀层/焊球材料：NIPDAU，TI官网BQ2060A-E619DBQ的批量USD价格：7.532（1000+）

BQ2060A-E619DBQR，工作温度：-20 to 70，封装：SSOP (DBQ)-28，包装数量MPQ：2500个，MSL 等级/回流焊峰值温度：Level-2-260C-1 YEAR，引脚镀层/焊球材料：NIPDAU，TI官网BQ2060A-E619DBQR的批量USD价格：6.416（1000+）

GPCCEDV — gpccedv

Gauging Parameter Calculator (GPC) is a math calculation and simulation tool that helps the battery designer to obtain matching Compensated End of Discharge Voltage (CEDV) coefficients for the specific battery profile. The tool allows the user to increase the accuracy of the fuel gauge IC over (...)

EV2200 Software for bq2060

监测参数计算器 (GPC) 是一种数学计算和仿真工具，可帮助电池设计人员获取匹配特定电池曲线的补偿放电终点电压 (CEDV) 系数。利用该工具，用户可以提高过热电量监测计 IC 的准确度。