The BQ21062 is a highly integrated battery charge management IC that integrates the most common functions for wearable, portable and small medical devices, namely a charger, a regulated output voltage rail for system power, a Load Switch/LDO, and push-button controller.

The BQ21062 IC integrates a linear charger with Power Path that enables quick and accurate charging for small batteries while providing a regulated voltage to the system. The regulated system voltage (PMID) output may be configured through I²C based on the recommended operating condition of downstream IC’s and system loads for optimal system operation.

The device supports charge current up to 500 mA and supports termination current down to 0.5 mA for maximum charge. The battery is charged using a standard Li-Ion charge profile with three phases: pre-charge, constant current and constant voltage regulation.

The device integrates advanced power path management and control that allows the device to provide power to the system while charging the battery even with poor adapters. The host may also control the power path through I²C allowing it to disconnect the input adapter and/or battery without physically removing them. The single push-button input eliminates the need of a separate button controller IC reducing the total solution footprint. The push-button input can be used for wake functions or to reset the system. The low quiescent current during operation and shutdown enables maximum battery life. The input current limit, charge current, LDO output voltage, and other parameters are programmable through the I²C interface making the BQ21062 a very flexible charging solution. A voltage-based JEITA compatible (or standard HOT/COLD) battery pack thermistor monitoring input (TS) is included that monitors battery temperature and automatically changes charge parameters to prevent the battery from charging outside of its safe temperature range. The temperature thresholds are also programable through I²C allowing the host to customize the thermal charging profile. The charger is optimized for 5-V USB input, with 20-V absolute maximum tolerance to withstand line transients. The device also integrates a linear regulator to provide a quiet rail for radios or processors and can be independently sourced and controlled through I²C.

• Linear battery charger with 1.25-mA to 500-mA fast charge current range
  • 0.5% Accurate I2C programmable battery regulation voltage ranging from 3.6 V to 4.6 V in 10-mV steps
  • Configurable termination current supporting down to 0.5 mA
  • 20-V Tolerant input with typical 3.4-V to 5.5-V input voltage operating range
  • Programmable thermal charging profile, fully configurable hot, warm, cool and cold thresholds
• Power Path management for powering system and charging battery
  • I2C Programmable regulated system voltage (PMID) ranging from 4.4V to 4.9V in addition to battery voltage tracking and Input pass-though options
  • Dynamic power path management optimizes charging from weak adapters
  • Advanced I2C control allows host to disconnect the battery or adapter as needed
• I2C Configurable load switch or up to 150-mA LDO output
  • Programmable range from 0.6 V to 3.7 V in 100-mV steps
• Ultra low Iddq for extended battery life
  • 10-nA Ship mode battery Iq
  • 400-nA Iq While powering the system (PMID and VDD on)
• One push-button wake-up and reset input with adjustable timers
  • Supports system power cycle and HW reset
• 20-Pin 2-mm x 1.6-mm CSP package
• 11-mm2 Total solution size

• Number of series cells
• 1
• Charge current (Max) (A)
• 0.5
• Operating Vin (Max) (V)
• 5.5
• Cell chemistry
• Li-Ion/Li-Polymer, Lithium Phosphate/LiFePO4
• Battery charge voltage (Min) (V)
• 3.6
• Battery charge voltage (Max) (V)
• 4.6
• Absolute Vin (safety rating) (Max) ((V))
• 20
• Control interface
• I2C
• Features
• BAT temp thermistor monitoring (JEITA profile), BAT temp thermistor monitoring (hot/cold profile), IC thermal regulation, IINDPM (Input current limit), Input OVP, Integrated LDO, Power Path, VINDPM (Input voltage threshold to maximize adaptor power)
• Operating Vin (Min) (V)
• 3.15
• Rating
• Catalog

BQ21062的完整型号有：BQ21062YFPR，以下是这些产品的关键参数及官网采购报价：

BQ21062YFPR，工作温度：-40 to 85，封装：DSBGA (YFP)-20，包装数量MPQ：3000个，MSL 等级/回流焊峰值温度：Level-1-260C-UNLIM，引脚镀层/焊球材料：SNAGCU，TI官网BQ21062YFPR的批量USD价格：1.11（1000+）

EV2400 — EV2400 评估模块接口板

The EV2400 EVM interface board enables an IBM-compatible or other type PC (with the required driver for its particular platform) to communicate with the Texas Instruments SMBus or I2C interface gas gauges via a Universal Serial Bus (USB) port. In addition to this board, PC software is required to (...)