The bqTINY™ III-series of devices are highly integrated Li-ion linear chargers and system power-path management devices targeted at space-limited portable applications. The bqTINY III-series offer integrated USB-port and DC supply (AC adapter), power-path management with autonomous power-source selection, power FETs and current sensors, high accuracy current and voltage regulation, charge status, and charge termination, in a single monolithic device.

The bqTINY III-series powers the system while independently charging the battery. This feature reduces the charge and discharge cycles on the battery, allows for proper charge termination and allows the system to run with an absent or defective battery pack. This feature also allows for the system to instantaneously turn on from an external power source in the case of a deeply discharged battery pack. The IC design is focused on supplying continuous power to the system when available from the AC, USB, or battery sources.

The power select pin, PSEL, defines which input source is to be used first (primary source – AC or USB). If the primary source is not available, then the IC automatically switches over to the other secondary source if available or the battery as the last option. If the PSEL is set low, the USB input is selected first and if not available, the AC line is selected (if available) but programmed to a USB input limiting rate (100 mA/500 mA max). This feature allows the use of one input connector, where the host programs the PSEL pin according to what source is connected (AC adaptor or USB port).

The bq24038 replaces USBPG with pin VBSEL, to enable user selection of the charge voltage. In addition, pin ACPG was modified to PG. PG is active low when either ac power or USB power is detected.

The ISET1 pin programs the battery&3146;s fast charge constant current level with a resistor. During normal AC operation, the input supply provides power to both the OUT (System) and BAT pins. For peak or excessive loads (typically when operating from the USB power, PSEL = Low) that would cause the input source to enter current limit (or Q3 - USB FET limiting current) and its source and system voltage (OUT pin) to drop, the dynamic power-path management (DPPM) feature reduces the charging current attempting to prevent any further drop in system voltage. This feature allows the selection of a lower current rated adaptor based on the average load (I_SYS-AVG + I_BAT-PGM ) rather than a high peak transient load.

• Small 3.5-mm × 4.5-mm QFN Package
• Designed for Single-Cell Li-Ion- or Li-Polymer- Based Portable Applications
• Integrated Dynamic Power-Path Management (DPPM) Feature Allowing the AC Adapter or the USB Port to Simultaneously Power the System and Charge the Battery
• Power Supplement Mode Allows Battery to Supplement the USB or AC Input Current
• Autonomous Power Source Selection (AC Adapter or USB)
• Integrated USB Charge Control With Selectable 100-mA and 500-mA Maximum Input Current Regulation Limits
• Dynamic Total Current Management for USB
• Supports Up to 2-A Total Current
• 3.3-V Integrated LDO Output
• Thermal Regulation for Charge Control
• Charge Status Outputs for LED or System Interface Indicates Charge and Fault Conditions
• Reverse Current, Short-Circuit, and Thermal Protection
• Power Good (AC Adapter and USB Port Present) Status Outputs
• Charge Voltage Options: 4.1 V, 4.2 V, or 4.36 V
• APPLICATIONS
  • Smart Phones and PDAs
  • MP3 Players
  • Digital Cameras Handheld Devices
  • Internet Appliances

All other trademarks are the property of their respective owners

• Number of series cells
• 1
• Charge current (Max) (A)
• 1.5
• Operating Vin (Max) (V)
• 16
• Cell chemistry
• Li-Ion/Li-Polymer
• Battery charge voltage (Min) (V)
• 4.1
• Battery charge voltage (Max) (V)
• 4.1
• Absolute Vin (safety rating) (Max) ((V))
• 18
• Control interface
• Standalone (RC-Settable)
• Features
• BAT temp thermistor monitoring (hot/cold profile), Integrated LDO, Power Path
• Operating Vin (Min) (V)
• 4.35
• Rating
• Catalog

BQ24031的完整型号有：BQ24031RHLR、BQ24031RHLT，以下是这些产品的关键参数及官网采购报价：

BQ24031RHLR，工作温度：-40 to 125，封装：VQFN (RHL)-20，包装数量MPQ：3000个，MSL 等级/回流焊峰值温度：Level-2-260C-1 YEAR，引脚镀层/焊球材料：NIPDAU，TI官网BQ24031RHLR的批量USD价格：1.663（1000+）

BQ24031RHLT，工作温度：-40 to 125，封装：VQFN (RHL)-20，包装数量MPQ：250个，MSL 等级/回流焊峰值温度：Level-2-260C-1 YEAR，引脚镀层/焊球材料：NIPDAU，TI官网BQ24031RHLT的批量USD价格：1.996（1000+）

BQ24031EVM — 针对 6V 电池进行了调节的 BQ24031 评估模块

The EVM provides a convenient method for evaluating the performance of a charge managementand system power solution for portable applications using the bq24031. A fully designed and tested module is presented. The bq24030/1 has a LDO 6V regulator connected to the OUT pin. The intent of this (...)

TEMPSENSE-SW — 温度传感设计软件

The TempSense Designer software allows the user to easily design temperature sensing circuits for many of the Texas Instruments battery charger devices. A full listing of the supported devices is included under the "Support" menu in the program. The user can use the thermisters included in the (...)