The BQ25123 is a highly integrated battery charge management IC that integrates the most common functions for wearable devices: Linear charger, regulated output, load switch, manual reset with timer, and battery voltage monitor. The integrated buck converter is a high efficiency, low I_Q switcher using DCS control that extends light load efficiency down to 10-µA load currents. The low quiescent current during operation and shutdown enables maximum battery life. The device supports charge currents from 5 mA to 300 mA. The input current limit, charge current, buck converter output voltage, LDO output voltage, and other parameters are programmable through the I²C interface.

The battery is charged using a standard Li-Ion charge profile with three phases: precharge, constant current and constant voltage. A voltage-based JEITA compatible battery pack thermistor monitoring input (TS) is included that monitors battery temperature and automatically changes charge parameters to prevent the battery from charging outside of its safe temperature range. The charger is optimized for 5-V USB input, with 20-V tolerance to withstand line transients. The buck converter is run from the input or battery. When in battery only mode, the device can run from a battery up to 4.65 V.

A configurable load switch allows system optimization by disconnecting infrequently used devices. The manual reset with timer allows multiple different configuration options for wake are reset optimization. A simple voltage based monitor provides battery level information to the host in 2% increments from 60% to 100% of the programmed V_(BATREG).

• Increases system operation time between charges
  • Configurable 300-mA buck regulator
  • 700-nA (typical) Iq with buck converter enabled (no load)
  • Configurable load switch or 100-mA LDO output
  • Up to 300-mA charge current for fast charging
  • 0.5% accurate battery voltage regulation (configurable from 3.6 V to 4.65 V in 10-mV steps)
  • Configurable termination current down to 500 μA
  • Simple voltage based battery monitor
• Highly integrated solution with small footprint
  • 2.5 mm x 2.5 mm WCSP package and 6 external components for minimal solution
  • Push-button wake-up and reset with adjustable timers
  • Power path management for powering the system and charging the battery
  • Power path management enables <50-nA Ship Mode battery quiescent current for longest shelf life
  • Battery charger operates from 3.4 V – 5.5 VIN (5.5-V OVP / 20-V tolerant)
  • Dedicated pins for input current limit, charge current, termination current, and status output
• I2C communication control
  • Charge voltage and current
  • Termination threshold
  • Input current limit
  • VINDPM threshold
  • Timer options
  • Load switch control
  • Controls for interrupts for faults and status
  • System output voltage adjustment
  • LDO output voltage adjustment

• Number of series cells
• 1
• Charge current (Max) (A)
• 0.3
• Operating Vin (Max) (V)
• 5.5
• Cell chemistry
• Li-Ion/Li-Polymer, Lithium Phosphate/LiFePO4
• Battery charge voltage (Min) (V)
• 3.6
• Battery charge voltage (Max) (V)
• 4.65
• Absolute Vin (safety rating) (Max) ((V))
• 20
• Control interface
• I2C
• Features
• BAT temp thermistor monitoring (JEITA profile), IC thermal regulation, Input OVP, Integrated LDO, Integrated buck converter, Power Path
• Operating Vin (Min) (V)
• 3.4
• Rating
• Catalog

BQ25123的完整型号有：BQ25123YFPR、BQ25123YFPT，以下是这些产品的关键参数及官网采购报价：

BQ25123YFPR，工作温度：-40 to 85，封装：DSBGA (YFP)-25，包装数量MPQ：3000个，MSL 等级/回流焊峰值温度：Level-1-260C-UNLIM，引脚镀层/焊球材料：SNAGCU，TI官网BQ25123YFPR的批量USD价格：1.4（1000+）

BQ25123YFPT，工作温度：-40 to 85，封装：DSBGA (YFP)-25，包装数量MPQ：250个，MSL 等级/回流焊峰值温度：Level-1-260C-UNLIM，引脚镀层/焊球材料：SNAGCU，TI官网BQ25123YFPT的批量USD价格：1.68（1000+）

BQ25123YFPR，工作温度：-40 to 85，封装：DSBGA (YFP)-25，包装数量MPQ：3000个，MSL 等级/回流焊峰值温度：Level-1-260C-UNLIM，引脚镀层/焊球材料：SNAGCU，TI官网BQ25123YFPR的批量USD价格：1.4（1000+）

BQ25123YFPT，工作温度：-40 to 85，封装：DSBGA (YFP)-25，包装数量MPQ：250个，MSL 等级/回流焊峰值温度：Level-1-260C-UNLIM，引脚镀层/焊球材料：SNAGCU，TI官网BQ25123YFPT的批量USD价格：1.68（1000+）