The BQ25618E/619E integrates charge and voltage protection in a single device. It offers low termination current for switching chargers to charge wearable devices to full battery capacity. The BQ25618E/BQ25619E low quiescent current reduces battery leakage down to 7 µA in Ship Mode, which conserves battery energy to extend the shelf life for the device. The BQ25619E is in a 4 mm x 4 mm QFN package for easy layout. The BQ25618E is in a 2.0 mm x 2.4 mm WCSP package for space-limited designs.

The BQ25618E/619E is a highly integrated 1.5-A switch-mode battery charge management and system power path management device for Li-ion and Li-polymer battery. It features fast charging with high input voltage support for a wide range of applications including earbuds (True Wireless or TWS), earphone charging case, and wearables. Its low impedance power path optimizes switch-mode operation efficiency, reduces battery charging time, and extends battery run time during discharging phase. Its input voltage and current regulation, low termination current,and battery remote sensing deliver maximum charging power to the battery. The solution is highly integrated with input reverse-blocking FET (RBFET, Q1), high-side switching FET (HSFET, Q2), low-side switching FET (LSFET, Q3), and battery FET (BATFET, Q4) between system and battery. It also integrates the bootstrap diode for the high-side gate drive for simplified system design. The I²C serial interface with charging and system settings makes the device a truly flexible solution.

The device supports a wide range of input sources, including standard USB host port, USB charging port, USB compliant high voltage adapter and wireless power. It is compliant with USB 2.0 and USB 3.0 power spec with input current and voltage regulation. The device takes the result from the detection circuit in the system, such as USB PHY device.

The power path management regulates the system slightly above battery voltage but does not drop below 3.5-V minimum system voltage (programmable) with adapter applied. With this feature, the system maintains operation even when the battery is completely depleted or removed. When the input current limit or voltage limit is reached, the power path management automatically reduces the charge current. As the system load continues to increase, the battery starts to discharge the battery until the system power requirement is met. This supplement mode prevents overloading the input source.

The device initiates and completes a charging cycle without software control. It senses the battery voltage and charges the battery in three phases: pre-conditioning, constant current and constant voltage. At the end of the charging cycle, the charger automatically terminates when the charge current is below a preset limit and the battery voltage is higher than the recharge threshold. If the fully charged battery falls below the recharge threshold, the charger automatically starts another charging cycle.

The charger provides various safety features for battery charging and system operations, including battery negative temperature coefficient thermistor monitoring, charging safety timer and overvoltage and over-current protections. Thermal regulation reduces charge current when the junction temperature exceeds 110°C. The status register reports the charging status and any fault conditions. With I²C, the VBUS_GD bit indicates if a good power source is present, and the INT output immediately notifies host when a fault occurs.

The device also provides the QON pin for BATFET enable and reset control to exit low power ship mode or full system reset function.

The BQ25619E device is available in a 24-pin, 4 mm × 4 mm x 0.75 mm thin WQFN package. The BQ25618E is available in a 30-ball, 2.0 mm x 2.4 mm WCSP package.

• High-efficiency, 1.5-MHz, synchronous Switch Mode buck charger
  • 95.5% charge efficiency at 0.5 A and 94.5% efficiency at 1 A
  • ±0.5% charge voltage regulation (10-mV step)
  • I2C programmable JEITA profile of charge voltage, current and temperature thresholds
  • Low termination current with high accuracy 20 mA±10 mA
  • Small inductor form factor of 2.5 x 2.0 x 1.0 mm3
• Single input supporting USB input, high-voltage adapter, or wireless power
  • Support 4-V to 13.5-V input voltage range with 22-V absolute max input rating
  • Programmable input current limit (IINDPM) with I2C (100 mA to 3.2 A, 100-mA/step)
  • Maximum power tracking by input voltage limit (VINDPM) up to 5.4 V
  • VINDPM threshold automatically tracks battery voltage
• Narrow voltage DC (NVDC) power path management
  • System instant-on with no battery or deeply discharged battery
• Flexible I2C configuration and autonomous charging for optimal system performance
• High integration includes all MOSFETs, current sensing and loop compensation
• Low RDSON 19.5-mΩ BATFET to minimize charging loss and extend battery run time
  • BATFET control for Ship Mode, and full system reset with and without adapter
• 7-μA low battery leakage current in Ship Mode
• 9.5-μA low battery leakage current with system standby
• High accuracy battery charging profile
  • ±6% charge current regulation
  • ±7.5% input current regulation
  • Remote battery sensing to charge faster
  • Programmable top-off timer for full battery charging

• Number of series cells
• 1
• Charge current (Max) (A)
• 1.5
• Operating Vin (Max) (V)
• 13.5
• Cell chemistry
• Li-Ion/Li-Polymer, Lithium Phosphate/LiFePO4
• Battery charge voltage (Min) (V)
• 3.5
• Battery charge voltage (Max) (V)
• 4.52
• Absolute Vin (safety rating) (Max) ((V))
• 22
• Control interface
• I2C
• Features
• BAT temp thermistor monitoring (JEITA profile), IC thermal regulation, IINDPM (Input current limit), Input OVP, Power Path, VINDPM (Input voltage threshold to maximize adaptor power)
• Operating Vin (Min) (V)
• 3.9
• Rating
• Catalog

BQ25618E的完整型号有：BQ25618EYFFR，以下是这些产品的关键参数及官网采购报价：

BQ25618EYFFR，工作温度：-40 to 85，封装：DSBGA (YFF)-30，包装数量MPQ：3000个，MSL 等级/回流焊峰值温度：Level-1-260C-UNLIM，引脚镀层/焊球材料：SNAGCU，TI官网BQ25618EYFFR的批量USD价格：1.09（1000+）

BQ25618EVM — BQ25618EVM

The BQ25618EVMis an evaulation module (EVM) used to test theBQ25618 device, a 1.5-A single-cell battery charger optimized for power bank applications in low power portable designs. The OTG reverse synchronous boost operation and forward buck mode operation allows for control over power (...)