The BQ25798 is a fully integrated switch-mode buck-boost charger for 1-4 cell Li-ion batteries and Li-polymer batteries. The integration includes 4 switching MOSFETs, input and charging current sensing circuits, the battery FET and all the loop compensation of the buck-boost converter. It uses NVDC power path management, regulating the system not dropping below a configurable minimum system voltage. When system power exceeds the input source rating, battery supplement mode supports the system without overloading the input source. BQ25798It also maximizes power from photovoltaic panels using its built-in V_OC scaling MPPT algorithm.BQ25798 supports ultra-fast switchover from the adapter to a converted battery voltage in Backup Mode.

The charger supports the narrow VDC power path management, in which the system is regulated at a voltage slightly higher than the battery voltage without being allowed to drop below the minimum system voltage. The minimum system voltage allows the system to operate even when the battery is completely discharged or removed. When system power exceeds the input source rating, battery supplement mode supports the system power requirement without overloading the input source.

The device charges a battery from a wide range of the input sources including legacy USB adapter to high voltage USB PD adapter and traditional barrel adapter. The charger automatically sets converter to be buck, boost or buck-boost configurations based on input voltage and battery voltage without the host control. The dual input source selector manages the power flowing from two different input sources. The inputs selection is controlled by the host through I2C with default source #1 (VAC1) as the primary input and the source #2 (VAC2) as the secondary input.

To support fast charging using adjustable high voltage adapter, the device provides D+/D- handshake. The device is compliant with USB 2.0 and USB 3.0 power delivery specification with input current and voltage regulation. In addition, the Input Current Optimizer (ICO) allows the detection of maximum power point of an unknown input source. The BQ25798 also provides a Maximum Power Point Tracking (MPPT) algorithm to optimize the power drawn when connected to a solar cell.

Besides the I²C host controlled charging mode, this charger also supports autonomous charging mode. After power up, the charging is enabled with default register settings. The device can complete a charging cycle without any software engagements. It detects battery voltage and charges the battery in different phases: trickle charging, pre-charging, constant current (CC) charging and constant voltage (CV) charging. At the end of the charging cycle, the charger automatically terminates when the charge current is below a pre-set limit (termination current) in the constant voltage phase. When the full battery falls below the recharge threshold, the charger will automatically start another charging cycle.

In the absence of input sources, this device supports USB On-the-Go (OTG) function, discharging battery to generate an adjustable 2.8-V to 22-V voltage on VBUS with 10-mV step size, which is compliant to the USB PD 3.0 specification defined programmable power supply (PPS) feature. The BQ25798 also provides backup mode to supply a system load at PMID using the adjustable OTG voltage when the adapter is removed.

The charger provides various safety features for battery charging and system operations, including battery temperature negative thermistor monitoring, trickle charge, pre-charge and fast charge timers and over-voltage/overcurrent protections on battery and input. The thermal regulation reduces charge current when the junction temperature exceeds a programmable threshold. The STAT output of the device reports the charging status and any fault conditions. The PG output indicates if a good power source is present. The INT pin immediately notifies host when fault occurs.

It is available in a 29-pin 4mm × 4mm QFN package.

• High power density, high integration buck-boost charger for 1-4 cell batteries supporting any USB PD 3.0 profile
  • Integrates four switching MOSFETs, BATFET
  • Integrates input and charging current sensing
• Highly efficient
  • 750-kHz or 1.5-MHz switching frequencies
  • 5-A charging current with 10-mA resolution
    • 96.5% efficient: 16-V battery at 3A from 20V
• Supports a wide range of input sources
  • Autonomously sampled VOC maximum power point tracking (MPPT) for charging from a photovoltaic panel
  • 3.6-V to 24-V wide input operating voltage range with 30-V absolute maximum rating
  • Detects USB BC1.2, HVDCP and non-standard adapters
• Dual-input power mux controller (optional)
• Narrow voltage DC (NVDC) power path
• Backup Mode with Ultra-fast switchover to adjustable voltage
• Powers USB port from battery (USB OTG)
  • 2.8-V to 22-V OTG output voltage with 10-mV resolution to support USB-PD PPS
  • OTG output current regulation up to 3.32 A with 40-mA resolution
• Flexible autonomous and I2C mode for optimal system performance
• Integrated 16-bit ADC for voltage, current, and temperature monitoring
• Low battery quiescent current
  • 17 μA for battery only operation
  • 500 nA in Charger Shutdown Mode
• High accuracy
  • -0.25% to +0.65% charge voltage regulation for 2S batteries
  • ±5% charge current regulation
  • ±5% input current regulation
• Safety
  • Thermal regulation and thermal shutdown
  • Input/battery OVP and OCP
  • Converter MOSFETs OCP
  • Charging safety timer
• Package
  • 29-Pin 4 mm × 4 mm QFN

• Number of series cells
• 1, 2, 3, 4
• Charge current (Max) (A)
• 5
• Operating Vin (Max) (V)
• 24
• Cell chemistry
• Li-Ion/Li-Polymer, Lithium Phosphate/LiFePO4
• Battery charge voltage (Min) (V)
• 3
• Battery charge voltage (Max) (V)
• 18.8
• Absolute Vin (safety rating) (Max) ((V))
• 30
• Control interface
• I2C
• Features
• BAT temp thermistor monitoring (JEITA profile), BAT temp thermistor monitoring (hot/cold profile), IC thermal regulation, ICO (Input Current Optimization), IINDPM (Input current limit), Input OVP, Integrated ADC, Integrated LDO, Power Path, Solar input/MPPT, USB C/PD compatible, USB D+/D-/BC1.2 integrated, USB OTG integrated, VINDPM (Input voltage threshold to maximize adaptor power)
• Operating Vin (Min) (V)
• 3.6
• Rating
• Catalog

BQ25798的完整型号有：BQ25798RQMR，以下是这些产品的关键参数及官网采购报价：

BQ25798RQMR，工作温度：-40 to 85，封装：VQFN-HR (RQM)-29，包装数量MPQ：3000个，MSL 等级/回流焊峰值温度：Level-2-260C-1 YEAR，引脚镀层/焊球材料：NIPDAU，TI官网BQ25798RQMR的批量USD价格：2.29（1000+）

BQ25798BKUPEVM — BQ25798 采用 QFN 封装的 I2C 控制型 5A、1 至 4 节降压/升压充电器评估模块

BQ25798BKUPEVM 评估模块 (EVM) 用于评估备用模式应用中的 BQ25798 器件。BQ25798 是一款采用 HOTROD (QFN) 封装的集成式开关模式降压/升压电池充电管理器件，适用于 1 至 4 节串联锂离子和锂聚合物电池，输入电压为 3.6V 至 24V，具有可编程的 750KHz 和 1500KHz 开关频率。具有充电和系统设置的 I2C 串行接口使得此器件成为一个真正灵活的解决方案。

BQ25798EVM — 具有双输入和 USB PD 3.0 OTG 输出的 I2C 控制型 1-4 节电池 5A 降压/升压充电器评估模块

The BQ25798EVM evaluation module (EVM) is used to evaluate the BQ25798 device. The BQ25798 is an integrated switched-mode buck-boost battery charge management device in HOTROD (QFN) package, intended for 1-series to 4-series cell Li-ion and Li-polymer batteries from 3.6-V to 24-V input with (...)

TI-CHARGER-GUI — 用于 USB2ANY 和电池充电评估模块的 GUI 软件

TI-CHARGER-GUI 提供基于网络的或独立的图形用户界面，可辅助评估、设计、配置或测试电池充电器产品。该软件可实现对寄存器的全面访问，并提供一个简单接口用于发送时序命令。