BQ79612-Q1, BQ79614-Q1 and BQ79616-Q1 provide high-accuracy cell voltage measurements in less than 200 µs for 12S, 14S and 16S battery modules in high-voltage battery management systems in HEV/EV. The family of monitors offers different channel options in the same package type, providing pin-to-pin compatibility and supporting high reuse of the established software and hardware across any platform. The integrated front-end filters enable the system to implement with simple, low voltage rating, differential RC filters on the cell input channels. The integrated, post-ADC, low-pass filters enable filtered, DC-like, voltage measurements for better state of charge (SOC) calculation. This device supports autonomous internal cell balancing with temperature monitoring to auto-pause and resume balancing to avoid an overtemperature condition.

The inclusion of the isolated, bidirectional, daisy chain ports supports both capacitor- and transformer-based isolation, allowing the use of the most effective components for centralized or distribution architectures commonly found in the xEV powertrain system. This device also includes eight GPIOs or auxiliary inputs that can be used for external thermistor measurements.

Host communication to the BQ7961x-Q1 family of devices can be connected via the device’s dedicated UART interface or through a communication bridge device, BQ79600. Additionally, an isolated, differential daisy-chain communication interface allows the host to communicate with the entire battery stack over a single interface. in the event of a communication line break, the daisy-chain communication interface is configurable to a ring architecture that allows the host to talk to devices at either end of the stack.

• Qualified for automotive applications
• AEC-Q100 Qualified with the following results:
  • Device temperature grade 1: –40°C to +125°C ambient operating temperature range
  • Device HBM ESD classification level 2
  • Device CDM ESD classification level C4B
• Functional Safety-Compliant
  • Developed for functional safety applications
  • Documentation to aid ISO 26262 system design
  • Systematic capability up to ASIL D
  • Hardware capability up to ASIL D
• +/- 1.5mV ADC accuracy
• Pin-package and software compatible device family:
  • Stackable monitor 16S (BQ79616-Q1, BQ79656-Q1) , 14S (BQ79614-Q1, BQ79654-Q1), and 12S (BQ79612-Q1, BQ79652-Q1)
  • Standalone monitor 48 V system (BQ75614-Q1)
• Built-in redundancy path for voltage and temperature diagnostics
• Highly accurate cell voltage measurements within 128 μs for all cell channels
• Integrated post-ADC configurable digital low-pass filters
• Supports bus bar connection and measurement
• Built-in host-controlled hardware reset to emulate POR-like device reset
• Supports internal cell balancing
  • Balancing current at 240 mA
  • Built-in balancing thermal management with automatic pause and resume control
• Isolated differential daisy chain communication with optional ring architecture
• Embedded fault signal and heartbeat through communication line
• UART/SPI host interface/communication bridge device BQ79600-Q1
• Built-in SPI master

• Number of series cells (Min)
• 6
• Vin (Max) (V)
• 80
• Features
• Cell balancing, Integrated ADC, Multi-cell support, Open-wire detection, Overtemperature protection, Overvoltage protection, Separate MCU requirement, Stackable (built-in interface), Temperature sensing, Undertemperature protection, Undervoltage protection
• Number of series cells (Max)
• 12
• Rating
• Automotive

BQ79612-Q1的完整型号有：BQ79612PAPRQ1，以下是这些产品的关键参数及官网采购报价：

BQ79612PAPRQ1，工作温度：-40 to 125，封装：HTQFP (PAP)-64，包装数量MPQ：1000个，MSL 等级/回流焊峰值温度：Level-3-260C-168 HR，引脚镀层/焊球材料：NIPDAU，TI官网BQ79612PAPRQ1的批量USD价格：6.5（1000+）

BQ79616EVM-021 — 汽车类 16 节串联精密电池监控器、平衡器和集成保护器评估模块

The BQ79616EVM is an evaluation board for the BQ79616-Q1. The BQ79616-Q1 provides high accuracy, channel measurements for six to sixteen battery cells. With the inclusion of a daisy chain communication port, the BQ79616-Q1 device is stackable (up to 35 devices) to support large stack (...)