The CDC2536 is a high-performance, low-skew, low-jitter clock driver. It uses a phase-lock loop (PLL) to precisely align, in both frequency and phase, the clock output signals to the clock input (CLKIN) signal. It is specifically designed for use with synchronous DRAMs and popular microprocessors operating at speeds from 50 MHz to 100 MHz or down to 25 MHz on outputs configured as half-frequency outputs. The CDC2536 operates at 3.3-V V_CC and is designed to drive a 50-W transmission line. The CDC2536 also provides on-chip series-damping resistors, eliminating the need for external termination components.

The feedback (FBIN) input is used to synchronize the output clocks in frequency and phase to the input clock (CLKIN). One of the six output clocks must be fed back to FBIN for the PLL to maintain synchronization between CLKIN and the outputs. The output used as the feedback pin is synchronized to the same frequency as CLKIN.

The Y outputs can be configured to switch in phase and at the same frequency as CLKIN. The select (SEL) input configures three Y outputs to operate at one-half or double the CLKIN frequency, depending on which pin is fed back to FBIN (see Tables 1 and 2). All output signal duty cycles are adjusted to 50% independent of the duty cycle at the input clock.

Output-enable (OE)\ is provided for output control. When OE\ is high, the outputs are in the high-impedance state. When OE\ is low, the outputs are active. TEST is used for factory testing of the device and can be use to bypass the PLL. TEST should be strapped to GND for normal operation.

Unlike many products containing PLLs, the CDC2536 does not require external RC networks. The loop filter for the PLL is included on-chip, minimizing component count, board space, and cost.

Because it is based on PLL circuitry, the CDC2536 requires a stabilization time to achieve phase lock of the feedback signal to the reference signal. This stabilization time is required following power up and application of a fixed-frequency, fixed-phase signal at CLKIN, as well as following any changes to the PLL reference or feedback signals. Such changes occur upon change of SEL, enabling the PLL via TEST, and upon enable of all outputs via OE\.

The CDC2536 is characterized for operation from 0°C to 70°C.

• Low Output Skew for Clock-Distribution and Clock-Generation Applications
• Operates at 3.3-V VCC
• Distributes One Clock Input to Six Outputs
• One Select Input Configures Three Outputs to Operate at One-Half or Double the Input Frequency
• No External RC Network Required
• On-Chip Series Damping Resistors
• External Feedback Pin (FBIN) Is Used to Synchronize the Outputs to the Clock Input
• Application for Synchronous DRAM, High-Speed Microprocessor
• TTL-Compatible Inputs and Outputs
• Outputs Drive 50- Parallel-Terminated Transmission Lines
• State-of-the-Art EPIC-IIB? BiCMOS Design Significantly Reduces Power Dissipation
• Distributed VCC and Ground Pins Reduce Switching Noise
• Packaged in Plastic 28-Pin Shrink Small-Outline Package

EPIC-IIB is a trademark of Texas Instruments.

• Function
• Zero-delay
• Additive RMS jitter (Typ) (fs)
• 200
• Output frequency (Max) (MHz)
• 125
• Number of outputs
• 6
• Output supply voltage (V)
• 3.3
• Core supply voltage (V)
• 3.3
• Output skew (ps)
• 500
• Features
• Spread spectrum clocking (SSC)
• Operating temperature range (C)
• 0 to 70
• Rating
• Catalog
• Output type
• TTL
• Input type
• TTL

CDC2536的完整型号有：CDC2536DB、CDC2536DBR，以下是这些产品的关键参数及官网采购报价：

CDC2536DB，工作温度：0 to 70，封装：SSOP (DB)-28，包装数量MPQ：50个，MSL 等级/回流焊峰值温度：Level-1-260C-UNLIM，引脚镀层/焊球材料：NIPDAU，TI官网CDC2536DB的批量USD价格：4.99（1000+）

CDC2536DBR，工作温度：0 to 70，封装：SSOP (DB)-28，包装数量MPQ：2000个，MSL 等级/回流焊峰值温度：Level-1-260C-UNLIM，引脚镀层/焊球材料：NIPDAU，TI官网CDC2536DBR的批量USD价格：4.25（1000+）

CDC2536 IBIS Model

PSpice for TI 可提供帮助评估模拟电路功能的设计和仿真环境。此功能齐全的设计和仿真套件使用 Cadence 的模拟分析引擎。PSpice for TI 可免费使用，包括业内超大的模型库之一，涵盖我们的模拟和电源产品系列以及精选的模拟行为模型。

借助?PSpice for TI 的设计和仿真环境及其内置的模型库，您可对复杂的混合信号设计进行仿真。创建完整的终端设备设计和原型解决方案，然后再进行布局和制造，可缩短产品上市时间并降低开发成本。

在?PSpice for TI 设计和仿真工具中，您可以搜索 TI (...)