The DRV10983-Q1 device is a 3-phase sensorless motor driver with integrated power MOSFETs, which can provide continuous drive current up to 2 A. The device is specifically designed for cost-sensitive, low-noise, low-external-component-count fan and pump applications.

The DRV10983-Q1 device preserves register setting down to 4.5 V and delivers current to the motor with supply voltage as low as 6.2 V. If the power supply voltage is higher than 28 V, the device stops driving the motor and protects the DRV10983-Q1 circuitry. This function is able to handle a load dump condition up to 45 V.

TI provides DRV10983-Q1 tuning Guide for quick setup and tuning of the device for optimal performance.

• Device Options:
• DRV10983Q: Sleep Version
• DRV10983SQ: Standby Version

The DRV10983-Q1 device uses a proprietary sensorless control scheme to provide continuous sinusoidal drive, which significantly reduces the pure tone acoustics that typically occur as a result of commutation. The interface to the device is designed to be simple and flexible. The motor can be controlled directly through PWM, analog, or I²C inputs. Motor speed feedback is available through both the FG pin and the I²C interface simultaneously.

The DRV10983-Q1 device features an integrated buck regulator to step down the supply voltage efficiently to 5 V for powering both internal and external circuits. The 3.3-V LDO also may be used to provide power for external circuits. The device is available in either a sleep mode or a standby mode version to conserve power when the motor is not running. The standby mode (8.5 mA) version (DRV10983SQ) leaves the regulator running and the sleep mode (48 µA) version (DRV10983Q) shuts the regulator off. Use the standby mode version in applications where the regulator is used to power an external microcontroller. Throughout this data sheet, the DRV10983-Q1 part number is used for both devices for example DRV10983Q (sleep version) and DRV10983SQ (standby version), except for specific discussions of sleep vs standby functionality.

An I²C interface allows the user to reprogram specific motor parameters in registers and to program the EEPROM to help optimize the performance for a given application. The DRV10983-Q1 device is available in a thermally-efficient HTSSOP, 24-pin package with an exposed thermal pad. The operating ambient temperature is specified from –40°C to 125°C.

• Qualified for automotive applications
• AEC-Q100 qualified with the following results:
  • Device temperature grade 1: –40°C to 125°C ambient operating temperature range
  • Device HBM ESD classification level 1C
  • Device CDM ESD classification level C4A
• Operation voltage range:
  • Motor operation, 6.2 V to 28 V
  • Register setting preserved, 4.5 V to 45 V
• Supports load dump voltage up to 45 V
• Total driver H + L rDS(on)
  • 250 mΩ at TA = 25°C
  • 325 mΩ at TA = 125°C
• Drive current: 2-A continuous winding current (3-A Peak)
• Configurable output PWM slew rate and frequency for EMI management
• Sensorless proprietary Back Electromotive Force (BEMF) control scheme (no need of hall sensors)
• Continuous sinusoidal 180° commutation
• Initial position-detect algorithm to avoid back spin during start-up
• No external sense resistor required
• Flexible user interface options:
  • I2C interface: access registers for command and feedback
  • Dedicated SPEED pin: accepts either analog or PWM input
  • Dedicated FG pin: provides TACH feedback
  • Spin-up profile can be customized with EEPROM
  • Forward-reverse control with DIR pin
• Integrated buck converter to efficiently provide 5?V and 3.3-V LDOs for internal and external circuits
• Supply current 8.5 mA with standby version (DRV10983SQ)
• Supply current of 48 μA with sleep version (DRV10983Q)
• Protection features
  • Overcurrent protection (protection for phase-to-phase, phase-to-GND and phase-to-vCC shorts
  • Lock detection
  • Anti-Voltage Surge (AVS) protection
  • UVLO protection
  • Thermal shutdown protection
• Thermally enhanced package

• Rating
• Automotive
• Architecture
• Integrated FET
• Control topology
• Sensorless, Sinusoidal
• Control interface
• 1xPWM, Analog, Serial
• Vs (Min) (V)
• 6.2
• Vs ABS (Max) (V)
• 45

DRV10983-Q1的完整型号有：DRV10983QPWPRQ1、DRV10983SQPWPRQ1，以下是这些产品的关键参数及官网采购报价：

DRV10983QPWPRQ1，工作温度：-40 to 125，封装：HTSSOP (PWP)-24，包装数量MPQ：2000个，MSL 等级/回流焊峰值温度：Level-3-260C-168 HR，引脚镀层/焊球材料：NIPDAU，TI官网DRV10983QPWPRQ1的批量USD价格：1.639（1000+）

DRV10983SQPWPRQ1，工作温度：-40 to 125，封装：HTSSOP (PWP)-24，包装数量MPQ：2000个，MSL 等级/回流焊峰值温度：Level-3-260C-168 HR，引脚镀层/焊球材料：NIPDAU，TI官网DRV10983SQPWPRQ1的批量USD价格：1.639（1000+）

DRV10983Q1EVM — DRV10983-Q1 evaluation board, 12-V, 24-Vautomotive three-phase, sensorless brushless DC mot

TheDRV10983Q1EVM evaluation module (EVM) serves as a user-friendly evaluation kit to demonstrate TI's brushless motor driver, DRV10983-Q1. The EVM is a high-performance, power-efficient, cost-effective platform that speeds development for quicker time to market. DRV10983Q1EVM supports (...)

DRV109xx Software (Rev. A)

此参考设计是使用 DRV10983-Q1 电机驱动器和 MSP430G2553 微控制器 (MCU) 的无传感器 BLDC 电机正弦驱动器。MCU 仅用于速度控制，而 DRV 器件是具有集成式 FETS 的主电机驱动器，用于驱动电机。此设计专门用于小型电机模块，尤其是风扇。此设计可实现专有无传感器控制，并可对电机参数进行调优，从而优化最终应用的性能。

TIDA-01373 — EEPROM 编程工具参考设计

TIDA-01373 是一款可扩展编程工具的参考硬件和软件示例，适用于 DRV10983、DRV10975、DRV10983-Q1 和 DRV10987 集成型 BLDC 电机驱动器。这些器件采用需要设置为特定于电机参数的可配置 EEPROM 寄存器。此参考设计提供了有关如何同时将多达 8 个电机驱动器器件编程为特定于用户的 EEPROM 电机参数值的详细信息。