The DS3668 quad peripheral driver is designed for those applications where low operating power, high breakdown voltage, high output current and low output ON voltage are required. Unlike most peripheral drivers available, a unique fault protected circuit is incorporated on each output. When the load current exceeds 1.0A (approximately) on any output for more than a built-in delay time, nominally 12 µs, that output will be shut off by its protection circuitry with no effect on other outputs. This condition will prevail until that protection circuitry is reset by toggling the corresponding input or the enable pin low for at least 1.0 µs. This built-in delay is provided to ensure that the protection circuitry is not triggered by turn-on surge currents associated with certain kinds of loads.

The DS3668's inputs combine TTL compatibility with high input impedance. In fact, its extreme low input current allows it to be driven directly by a MOS device. The outputs are capable of sinking 600 mA each and offer a 70V breakdown. However, for inductive loads the output should be clamped to 35V or less to avoid latch up during turn off (inductive fly-back protection - refer AN-213). An on-chip clamp diode capable of handling 800 mA is provided at each output for this purpose. In addition, the DS3668 incorporates circuitry that guarantees glitch-free power up or down operation and a fail-safe feature which puts the output in a high impedance state when the input is open.

The molded package is specifically constructed to allow increased power dissipation over conventional packages. The four ground pins are directly connected to the device chip with a special copper lead frame. When the quad driver is soldered into a PC board, the power rating of the device improves significantly.

---

• Output fault protection
• High impedance TTL compatible inputs
• High output current-600 mA per output
• No output latch-up at 35V
• Low output ON voltage (550 mV typ @ 600 mA)
• High breakdown voltage (70V)
• Open collector outputs
• Output clamp diodes for inductive fly-back protection
• NPN inputs for minimal input currents (1 μA typical)
• Low operating power
• Standard 5V power supply
• Power up/down protection
• Fail-safe operation
• 2W power package
• Pin-for-pin compatible with SN75437

• Drivers per package
• 4
• Switching voltage (Max) (V)
• 70
• Output voltage (Max) (V)
• 70
• Peak output current (mA)
• 600
• Delay time (Typ) (ns)
• 300
• Input compatibility
• CMOS, TTL
• Vol @ lowest spec current (Typ) (mV)
• 200
• Iout/ch (Max) (mA)
• 600
• Iout_off (Typ) (uA)
• 100
• Rating
• Catalog

DS3668的完整型号有：DS3668N/NOPB，以下是这些产品的关键参数及官网采购报价：

DS3668N/NOPB，工作温度：-40 to 125，封装：PDIP (N)-16，包装数量MPQ：25个，MSL 等级/回流焊峰值温度：Level-1-NA-UNLIM，引脚镀层/焊球材料：NIPDAU，TI官网DS3668N/NOPB的批量USD价格：1.311（1000+）

PSPICE-FOR-TI — 适用于 TI 设计和模拟工具的 PSpice

PSpice for TI 可提供帮助评估模拟电路功能的设计和仿真环境。此功能齐全的设计和仿真套件使用 Cadence 的模拟分析引擎。PSpice for TI 可免费使用，包括业内超大的模型库之一，涵盖我们的模拟和电源产品系列以及精选的模拟行为模型。

借助?PSpice for TI 的设计和仿真环境及其内置的模型库，您可对复杂的混合信号设计进行仿真。创建完整的终端设备设计和原型解决方案，然后再进行布局和制造，可缩短产品上市时间并降低开发成本。

在?PSpice for TI 设计和仿真工具中，您可以搜索 TI (...)