The DS92LV090A is one in a series of Bus LVDS transceivers designed specifically for the high speed, low power proprietary backplane or cable interfaces. The device operates from a single 3.3V power supply and includes nine differential line drivers and nine receivers. To minimize bus loading, the driver outputs and receiver inputs are internally connected. The separate I/O of the logic side allows for loop back support. The device also features a flow through pin out which allows easy PCB routing for short stubs between its pins and the connector.

The driver translates 3V TTL levels (single-ended) to differential Bus LVDS (BLVDS) output levels. This allows for high speed operation, while consuming minimal power with reduced EMI. In addition, the differential signaling provides common mode noise rejection of ±1V.

The receiver threshold is less than ±100 mV over a ±1V common mode range and translates the differential Bus LVDS to standard (TTL/CMOS) levels. (See Section for more details.)

• Bus LVDS Signaling
• 3.2 Nanosecond Propagation Delay Max
• Chip to Chip Skew ±800ps
• Low Power CMOS Design
• High Signaling Rate Capability (Above 100 Mbps)
• 0.1V to 2.3V Common Mode Range for VID = 200mV
• ±100 mV Receiver Sensitivity
• Supports Open and Terminated Failsafe on Port Pins
• 3.3V Operation
• Glitch Free Power Up/Down (Driver & Receiver Disabled)
• Light Bus Loading (5 pF Typical) per Bus LVDS Load
• Designed for Double Termination Applications
• Balanced Output Impedance
• Product Offered in 64 Pin LQFP Package
• High Impedance Bus Pins on Power off (VCC = 0V)
• Driver Channel to Channel Skew (Same Device) 230ps Typical
• Receiver Channel to Channel Skew (Same Device) 370ps Typical

All trademarks are the property of their respective owners.

• Function
• Transceiver
• Protocols
• BLVDS
• Number of transmitters
• 9
• Number of receivers
• 9
• Supply voltage (V)
• 3.3
• Signaling rate (Mbps)
• 100
• Input signal
• LVTTL, BLVDS
• Output signal
• BLVDS, LVTTL, CMOS
• Rating
• Catalog
• Operating temperature range (C)
• -40 to 85

DS92LV090A的完整型号有：DS92LV090ATVEH/NOPB、DS92LV090ATVEHX/NOPB，以下是这些产品的关键参数及官网采购报价：

DS92LV090ATVEH/NOPB，工作温度：-40 to 85，封装：LQFP (PM)-64，包装数量MPQ：160个，MSL 等级/回流焊峰值温度：Level-3-260C-168 HR，引脚镀层/焊球材料：SN，TI官网DS92LV090ATVEH/NOPB的批量USD价格：4.663（1000+）

DS92LV090ATVEHX/NOPB，工作温度：-40 to 85，封装：LQFP (PM)-64，包装数量MPQ：1000个，MSL 等级/回流焊峰值温度：Level-3-260C-168 HR，引脚镀层/焊球材料：SN，TI官网DS92LV090ATVEHX/NOPB的批量USD价格：3.886（1000+）

DS92LV090A IBIS Model

PSpice for TI 可提供帮助评估模拟电路功能的设计和仿真环境。此功能齐全的设计和仿真套件使用 Cadence 的模拟分析引擎。PSpice for TI 可免费使用，包括业内超大的模型库之一，涵盖我们的模拟和电源产品系列以及精选的模拟行为模型。

借助?PSpice for TI 的设计和仿真环境及其内置的模型库，您可对复杂的混合信号设计进行仿真。创建完整的终端设备设计和原型解决方案，然后再进行布局和制造，可缩短产品上市时间并降低开发成本。

在?PSpice for TI 设计和仿真工具中，您可以搜索 TI (...)

TINA-TI — 基于 SPICE 的模拟仿真程序

TINA-TI 提供了 SPICE 所有的传统直流、瞬态和频域分析以及更多。TINA 具有广泛的后处理功能，允许您按照希望的方式设置结果的格式。虚拟仪器允许您选择输入波形、探针电路节点电压和波形。TINA 的原理图捕获非常直观 - 真正的“快速入门”。

TINA-TI 安装需要大约 500MB。直接安装，如果想卸载也很容易。我们相信您肯定会爱不释手。

TINA 是德州仪器 (TI) 专有的 DesignSoft 产品。该免费版本具有完整的功能，但不支持完整版 TINA 所提供的某些其他功能。

如需获取可用 TINA-TI 模型的完整列表，请参阅：SpiceRack - 完整列表

需要 HSpice (...)