The LM20124 is a full featured 1 MHz synchronous buck regulator capable of delivering up to 4A of continuous output current. The current mode control loop can be compensated to be stable with virtually any type of output capacitor. For most cases, compensating the device only requires two external components, providing maximum flexibility and ease of use. The device is optimized to work over the input voltage range of 2.95V to 5.5V making it suited for a wide variety of low voltage systems.

The device features internal over voltage protection (OVP) and over current protection (OCP) circuits for increased system reliability. A precision enable pin and integrated UVLO allows the turn-on of the device to be tightly controlled and sequenced. Start-up inrush currents are limited by both an internally fixed and externally adjustable Soft-Start circuit. Fault detection and supply sequencing is possible with the integrated power good circuit.

The LM20124 is designed to work well in multi-rail power supply architectures. The output voltage of the device can be configured to track a higher voltage rail using the SS/TRK pin. If the output of the LM20124 is pre-biased at startup it will not sink current to pull the output low until the internal soft-start ramp exceeds the voltage at the feedback pin.

The LM20124 is offered in a 16-pin TSSOP package with an exposed pad that can be soldered to the PCB, eliminating the need for bulky heatsinks.

• LM20124-Q1 is AEC-Q100 qualified and manufactured on an Automotive Grade Flow
• Input voltage range 2.95V to 5.5V
• Accurate current limit minimizes inductor size
• 96% efficiency at 1 MHz switching frequency
• 32 m? integrated FET switches
• Starts up into pre-biased loads
• Output voltage tracking
• Peak current mode control
• Adjustable output voltage down to 0.8V
• Adjustable Soft-Start with external capacitor
• Precision enable pin with hysteresis
• Integrated OVP, UVLO, power good and thermal shutdown
• TSSOP 16 pin exposed pad package

All trademarks are the property of their respective owners.

• Vin (Min) (V)
• 2.95
• Vin (Max) (V)
• 5.5
• Vout (Min) (V)
• 0.8
• Vout (Max) (V)
• 5
• Iout (Max) (A)
• 4
• Iq (Typ) (uA)
• 3500
• Switching frequency (Min) (kHz)
• 1000
• Switching frequency (Max) (kHz)
• 1000
• Features
• Enable, Power Good, Pre-Bias Start-Up, Synchronous Rectification, Tracking
• Rating
• Catalog
• Regulated outputs (#)
• 1
• Control mode
• Current Mode
• Duty cycle (Max) (%)
• 85

LM20124的完整型号有：LM20124MH/NOPB、LM20124MHE/NOPB、LM20124MHX/NOPB，以下是这些产品的关键参数及官网采购报价：

LM20124MH/NOPB，工作温度：-40 to 125，封装：HTSSOP (PWP)-16，包装数量MPQ：92个，MSL 等级/回流焊峰值温度：Level-1-260C-UNLIM，引脚镀层/焊球材料：SN，TI官网LM20124MH/NOPB的批量USD价格：1.336（1000+）

LM20124MHE/NOPB，工作温度：-40 to 125，封装：HTSSOP (PWP)-16，包装数量MPQ：250个，MSL 等级/回流焊峰值温度：Level-1-260C-UNLIM，引脚镀层/焊球材料：SN，TI官网LM20124MHE/NOPB的批量USD价格：1.336（1000+）

LM20124MHX/NOPB，工作温度：-40 to 125，封装：HTSSOP (PWP)-16，包装数量MPQ：2500个，MSL 等级/回流焊峰值温度：Level-1-260C-UNLIM，引脚镀层/焊球材料：SN，TI官网LM20124MHX/NOPB的批量USD价格：1.113（1000+）

PSPICE-FOR-TI — 适用于 TI 设计和模拟工具的 PSpice

PSpice for TI 可提供帮助评估模拟电路功能的设计和仿真环境。此功能齐全的设计和仿真套件使用 Cadence 的模拟分析引擎。PSpice for TI 可免费使用，包括业内超大的模型库之一，涵盖我们的模拟和电源产品系列以及精选的模拟行为模型。

借助?PSpice for TI 的设计和仿真环境及其内置的模型库，您可对复杂的混合信号设计进行仿真。创建完整的终端设备设计和原型解决方案，然后再进行布局和制造，可缩短产品上市时间并降低开发成本。

在?PSpice for TI 设计和仿真工具中，您可以搜索 TI (...)