LM2759 is an integrated low-noise, high-current switched capacitor DC/DC converter with a regulated current source. The device requires only four small ceramic capacitors making the total solution area less than 22 mm² and the height less than 1 mm. The LM2759 is capable of driving loads up to 1A from a single-cell Li-Ion battery. Maximum efficiency is achieved over the input voltage range by actively selecting the proper gain based on the LED forward voltage and current requirements.

The LED current can be programmed up to 1A via an I²C-compatible interface, along with eight selectable Flash Time-Out durations. One high-current Flash LED can be driven either in a high-power Flash mode or a low-power Torch mode. The Strobe pin allows the flash to be toggled via a Flash enable signal from a camera module. The TX input pin limits the Flash LED current to the Torch current level during a RF PA pulse, to reduce high loads on the battery. Internal soft-start circuitry limits the amount of inrush current during start-up.

LM2759 is offered in a small 12-pin thermally enhanced WSON package.

• Up to 1A Output Current
• Solution Area < 22 mm2
• No Inductor Required
• 90% Peak Efficiency
• Adaptive 1x, 1.5x and 2x Gains for Maximum Efficiency
• Load Disconnect in Shutdown
• Accurate Input Current Control During Gain Transitions
• Flash Time-Out
• TX Input Pin Ensures Synchronization with RF Power Amplifier Pulse
• Torch, Flash, and Indicator Modes
• External Flash Enable via Strobe Input Pin
• Strobe Input Disable via I2C
• Programmable Flash Pulse Duration, and Torch and Flash Currents via I2C-Compatible Interface
• 1MHz Constant Frequency Operation
• Low Profile 12–Pin WSON (3mm x 3mm x 0.8mm)

All trademarks are the property of their respective owners.

• Input voltage (type)
• DC/DC
• Topology
• Charge pump, Current Mode
• Vin (Min) (V)
• 2.7
• Vin (Max) (V)
• 5.5
• Iout (Max) (A)
• 1
• Iq (Typ) (mA)
• 3.4
• Features
• I2C Control
• Operating temperature range (C)
• -30 to 85
• Dimming method
• Analog, PWM

LM2759的完整型号有：LM2759SD/NOPB、LM2759SDX/NOPB，以下是这些产品的关键参数及官网采购报价：

LM2759SD/NOPB，工作温度：-30 to 85，封装：WSON (DQB)-12，包装数量MPQ：1000个，MSL 等级/回流焊峰值温度：Level-3-260C-168 HR，引脚镀层/焊球材料：SN，TI官网LM2759SD/NOPB的批量USD价格：.606（1000+）

LM2759SDX/NOPB，工作温度：-30 to 85，封装：WSON (DQB)-12，包装数量MPQ：4500个，MSL 等级/回流焊峰值温度：Level-3-260C-168 HR，引脚镀层/焊球材料：SN，TI官网LM2759SDX/NOPB的批量USD价格：.505（1000+）

PSPICE-FOR-TI — 适用于 TI 设计和模拟工具的 PSpice

PSpice for TI 可提供帮助评估模拟电路功能的设计和仿真环境。此功能齐全的设计和仿真套件使用 Cadence 的模拟分析引擎。PSpice for TI 可免费使用，包括业内超大的模型库之一，涵盖我们的模拟和电源产品系列以及精选的模拟行为模型。

借助?PSpice for TI 的设计和仿真环境及其内置的模型库，您可对复杂的混合信号设计进行仿真。创建完整的终端设备设计和原型解决方案，然后再进行布局和制造，可缩短产品上市时间并降低开发成本。

在?PSpice for TI 设计和仿真工具中，您可以搜索 TI (...)