- 制造厂商：TI
- 产品类别：传感器
- 技术类目：温度传感器和控制 IC - 数字温度传感器
- 功能描述：1 条本地通道温度传感器，带风扇转速控制功能和电源电压监控器
- 点击这里打开及下载LM96080的技术文档资料
- TI代理渠道，提供当日发货、严格的质量标准，满足您的目标价格
LM96080, compatible to LM80, is a hardware monitor that contains a 10-bit delta-sigma ADC capable of measuring 7 positive voltages and local temperature. The LM96080 also measures the speed of two fans and includes other hardware monitoring on an I2C® interface. The LM96080 includes a sequencer that performs WATCHDOG window comparisons of all measured values and its interrupt outputs become active when any values exceed the programmed limits.
The LM96080 is especially suited to interface to both linear and digital temperature sensors. The 2.5 mV LSb (least significant bit) and 2.56 volt input range is ideal for accepting inputs from a linear sensor such as the LM94022. The BTI is used as an input from either digital or thermostat sensors such as LM73, LM75, LM56, LM57, LM26, LM27, LM26LV, or other LM96080.
The LM96080 supports Standard Mode (Sm, 100 kbits/s) and Fast Mode (Fm, 400 kbits/s) I2C interface modes of operation. LM96080 includes an analog filter on the I2C digital control lines that allows improved noise immunity and supports TIMEOUT reset function on SDA and SCL that prevents I2C bus lockup. Three I2C device address pins allow up to 8 parts on a single bus.
The LM96080's 3.0V to 5.5V supply voltage range, low supply current, and I2C interface make it ideal for a wide range of applications. Operation is ensured over the temperature range of (−40)°C ≤ TA ≤ +125°C. The LM96080 is available in a 24-pin TSSOP package.
- Local Temperature Sensing
- 7 Positive Voltage Inputs with 10-bit Resolution
- 2 Programmable Fan Speed Monitoring Inputs
- 2.5 mV LSb and 2.56V Input Range
- Chassis Intrusion Detector Input
- WATCHDOG Comparison of All Monitored Values
- Separate Input to Show Status in Interrupt Status Register of Additional External Temperature Sensors Such as the LM26/27, LM56/57, LM73, or LM75
- I2C Serial Bus Interface Compatibility, Supports Standard Mode, 100 kbits/s, and Fast Mode, 400 kbits/s
- Shutdown Mode to Minimize Power Consumption
- Programmable RST_OUT/OS Pin: RST_OUT Provides a Reset Output; OS Provides an Interrupt Output Activated by an Overtemperature Shutdown Event
- Software and Pin Compatible with the LM80
- Total Unadjusted Error ±1 %FS (Max)
- Differential Non-Linearity ±1 Lsb (Max)
- Supply Voltage Range +3.0 V to +5.5 V
- Supply Current (Operating) 0.370 mA Typ
- Supply Current (Shutdown) 0.330 mA Typ
- ADC Resolution 10 Bits
- Temperature Resolution 0.5°C/0.0625°C
- Temperature Accuracy ±3°C (Max)
All trademarks are the property of their respective owners.
- Local sensor accuracy (Max) (+/- C)
- 2
- Type
- Fan Controller
- Operating temperature range (C)
- -40 to 125
- Supply voltage (Min) (V)
- 3
- Interface type
- I2C, SMBus
- Supply voltage (Max) (V)
- 5.5
- Supply current (Max) (uA)
- 580
- Temp resolution (Max) (bits)
- 12
- Features
- Tachometer, ALERT
- Remote channels (#)
- 0
- Addresses
- 8
- Rating
- Catalog
LM96080的完整型号有：LM96080CIMT/NOPB、LM96080CIMTX/NOPB，以下是这些产品的关键参数及官网采购报价：
LM96080CIMT/NOPB，工作温度：-40 to 125，封装：TSSOP (PW)-24，包装数量MPQ：61个，MSL 等级/回流焊峰值温度：Level-1-260C-UNLIM，引脚镀层/焊球材料：SN，TI官网LM96080CIMT/NOPB的批量USD价格：3.036（1000+）
LM96080CIMTX/NOPB，工作温度：-40 to 125，封装：TSSOP (PW)-24，包装数量MPQ：2500个，MSL 等级/回流焊峰值温度：Level-1-260C-UNLIM，引脚镀层/焊球材料：SN，TI官网LM96080CIMTX/NOPB的批量USD价格：2.53（1000+）
DIGITALTEMPSENSORSEVM-SW — 用于硬件监控器和数字温度传感器的评估板软件
Evaluation Board Software for Hardware Monitors and Digital Temperature SensorsLM80SW-LINUX — 用于 LM80 的 Linux 驱动程序
Linux 驱动程序支持 LM80 系列的系统硬件监控器。Linux 驱动程序支持通过 I2C 总线进行通信，并可与硬件监控子系统交互。Linux 主线状态
在 Linux 主线中提供：是
可通过 git.ti.com 获取：不适用
- lm80
- lm96080
与该器件关联的文件为：
drivers/hwmon/lm80.c
Linux 器件树文档(...)
SENSOREVAL — 用于硬件监控器和数字温度传感器的评估板软件
SensorEvalSensorEval 软件支持通过 USB 接口连接的 TI 最新温度传感器和硬件监控器评估板。此外，该软件还允许访问直接安装在支持 Intel 芯片组的主板上的传感器。
- 下载 SensorEval 软件和手册
- 为以下各项提供 Windows XP 支持：
- USB 评估板（LM93 除外）
- Intel ICHx 接口（ADCS9888、LM32、LM40、LM41、LM71、LM95010 和 LM95071 除外）
- “无硬件”模式支持在没有任何硬件的情况下运行软件
