The LMH6503 is a wideband, DC coupled, differential input, voltage controlled gain stage followed by a high-speed current feedback Op Amp which can directly drive a low impedance load. Gain adjustment range is more than 70dB for up to 10MHz.

Maximum gain is set by external components and the gain can be reduced all the way to cut-off. Power consumption is 370mW with a speed of 135MHz . Output referred DC offset voltage is less than 350mV over the entire gain control voltage range. Device-to-device Gain matching is within 0.7dB at maximum gain. Furthermore, gain at any V_G is tested and the tolerance is ensured. The output current feedback Op Amp allows high frequency large signals (Slew Rate = 1800V/μs) and can also drive heavy load current (75mA). Differential inputs allow common mode rejection in low level amplification or in applications where signals are carried over relatively long wires. For single ended operation, the unused input can easily be tied to ground (or to a virtual half-supply in single supply application). Inverting or non-inverting gains could be obtained by choosing one input polarity or the other.

To further increase versatility when used in a single supply application, gain control range is set to be from −1V to +1V relative to pin 11 potential (ground pin). In single supply operation, this ground pin is tied to a "virtual" half supply. Gain control pin has high input impedance to simplify its drive requirement. Gain control is linear in V/V throughout the gain adjustment range. Maximum gain can be set to be anywhere between 1V/V to 100V/V or higher. For linear in dB gain control applications, see LMH6502 datasheet.

The LMH6503 is available in the SOIC-14 and TSSOP-14 package.

• VS = ±5V, TA = 25°C, RF = 1k?, RG = 174?, RL = 100?, AV = AV(MAX) = 10, Typical Values Unless Specified.
• -3dB BW 135MHz
• Gain Control BW 100MHz
• Adjustment Range (Typical Over Temp) 70dB
• Gain Matching (Limit) ±0.7dB
• Slew Rate 1800V/μs
• Supply Current (No Load) 37mA
• Linear Output Current ±75mA
• Output Voltage (RL = 100?) ±3.2V
• Input Voltage Noise 6.6nV/√Hz
• Input Current Noise 2.4pA/√Hz
• THD (20MHz, RL = 100?, VO = 2VPP) ?57dBc
• Replacement for CLC522

All trademarks are the property of their respective owners.

• PGA/VGA
• VGA
• Number of channels (#)
• 1
• BW @ Acl (MHz)
• 135
• Vs (Max) (V)
• 12
• Vs (Min) (V)
• 5
• Acl, min spec gain (V/V)
• 1
• Gain (Max) (dB)
• 40
• Slew rate (Typ) (V/us)
• 1800
• Operating temperature range (C)
• -40 to 85
• Features
• Analog Gain Set, Differential to Single-ended conversion

LMH6503的完整型号有：LMH6503MA/NOPB、LMH6503MAX/NOPB、LMH6503MT/NOPB、LMH6503MTX/NOPB、LMH6503MT，以下是这些产品的关键参数及官网采购报价：

LMH6503MA/NOPB，工作温度：-40 to 85，封装：SOIC (D)-14，包装数量MPQ：55个，MSL 等级/回流焊峰值温度：Level-1-260C-UNLIM，引脚镀层/焊球材料：SN，TI官网LMH6503MA/NOPB的批量USD价格：4.165（1000+）

LMH6503MAX/NOPB，工作温度：-40 to 85，封装：SOIC (D)-14，包装数量MPQ：2500个，MSL 等级/回流焊峰值温度：Level-1-260C-UNLIM，引脚镀层/焊球材料：SN，TI官网LMH6503MAX/NOPB的批量USD价格：3.524（1000+）

LMH6503MT/NOPB，工作温度：-40 to 85，封装：TSSOP (PW)-14，包装数量MPQ：94个，MSL 等级/回流焊峰值温度：Level-1-260C-UNLIM，引脚镀层/焊球材料：SN，TI官网LMH6503MT/NOPB的批量USD价格：4.165（1000+）

LMH6503MTX/NOPB，工作温度：-40 to 85，封装：TSSOP (PW)-14，包装数量MPQ：2500个，MSL 等级/回流焊峰值温度：Level-1-260C-UNLIM，引脚镀层/焊球材料：SN，TI官网LMH6503MTX/NOPB的批量USD价格：3.524（1000+）

LMH6503MT，工作温度：-40 to 85，封装：TSSOP (PW)-14，包装数量MPQ：94个，MSL 等级/回流焊峰值温度：Level-1-260C-UNLIM，引脚镀层/焊球材料：SNPB，TI官网LMH6503MT的批量USD价格：5.287（1000+）

LMH730033 — 用于采用 14 引脚 SOIC 封装的高速单路可变增益放大器的评估板

National Semiconductor offers this unpopulated Evaluation Board to aid in the evaluation and testing of high-speed Variable Gain Amplifier that are offered in the 14-Pin SOIC package. Resistors, capacitors, or any other surface-mount components can be easily mounted on this board in the desired (...)

LMH6503 PSPICE Model

PSpice for TI 可提供帮助评估模拟电路功能的设计和仿真环境。此功能齐全的设计和仿真套件使用 Cadence 的模拟分析引擎。PSpice for TI 可免费使用，包括业内超大的模型库之一，涵盖我们的模拟和电源产品系列以及精选的模拟行为模型。

借助?PSpice for TI 的设计和仿真环境及其内置的模型库，您可对复杂的混合信号设计进行仿真。创建完整的终端设备设计和原型解决方案，然后再进行布局和制造，可缩短产品上市时间并降低开发成本。

在?PSpice for TI 设计和仿真工具中，您可以搜索 TI (...)

TINA-TI — 基于 SPICE 的模拟仿真程序

TINA-TI 提供了 SPICE 所有的传统直流、瞬态和频域分析以及更多。TINA 具有广泛的后处理功能，允许您按照希望的方式设置结果的格式。虚拟仪器允许您选择输入波形、探针电路节点电压和波形。TINA 的原理图捕获非常直观 - 真正的“快速入门”。

TINA-TI 安装需要大约 500MB。直接安装，如果想卸载也很容易。我们相信您肯定会爱不释手。

TINA 是德州仪器 (TI) 专有的 DesignSoft 产品。该免费版本具有完整的功能，但不支持完整版 TINA 所提供的某些其他功能。

如需获取可用 TINA-TI 模型的完整列表，请参阅：SpiceRack - 完整列表

需要 HSpice (...)