The LMH6611 (single, with shutdown) and LMH6612 (dual) are 345 MHz rail-to-rail output amplifiers consuming just 3.2 mA of quiescent current per channel and designed to deliver high performance in power conscious single supply systems. The LMH6611 and LMH6612 have precision trimmed input offset voltages with low noise and low distortion performance as required for high accuracy video, test and measurement, and communication applications. The LMH6611 and LMH6612 are members of the PowerWise family and have an exceptional power-to-performance ratio.

With a trimmed input offset voltage of 0.022 mV and a high open loop gain of 103 dB the LMH6611 and LMH6612 meet the requirements of DC sensitive high speed applications such as low pass filtering in baseband I and Q radio channels. These specifications combined with a 0.01% settling time of 100 ns, a low noise of 10 nV/√Hz and better than 102 dBc SFDR at 100 kHz make these amplifiers particularly suited to driving 10, 12 and 14-bit high speed ADCs. The 45 MHz 0.1 dB bandwidth (A_V = 2) driving 2 V_PP into 150Ω allows the amplifiers to be used as output drivers in 1080i and 720p HDTV applications.

The input common mode range extends from 200 mV below the negative supply rail up to 1.2V from the positive rail. On a single 5V supply with a ground terminated 150Ω load the output swings to within 49 mV of the ground, while a mid-rail terminated 1 kΩ load will swing to 77 mV of either rail.

The amplifiers will operate on a 2.7V to 11V single supply or ±1.35V to ±5.5V split supply. The LMH6611 single is available in 6-Pin SOT and has an independent active low disable pin which reduces the supply current to 120 µA. The LMH6612 is available in 8-Pin SOIC. Both the LMH6611 and LMH6612 are available in −40°C to +125°C extended industrial temperature grade.

• VS = 5V, RL = 1 kΩ, TA = 25°C and AV = +1, Unless Otherwise Specified.
• Operating Voltage Range 2.7V to 11V
• Supply Current Per Channel 3.2 mA
• Small Signal Bandwidth 345 MHz
• Open Loop Gain 103 dB
• Input Offset Voltage (Limit at 25°C) ±1.5 mV
• Slew Rate 460 V/μs
• 0.1 dB Bandwidth 45 MHz
• Settling Time to 0.1% 67 ns
• Settling Time to 0.01% 100 ns
• SFDR (f = 100 kHz, AV = 2, VOUT = 2 VPP) 102 dBc
• Low Voltage Noise 10 nV/√Hz
• Output current ±100 mA
• CMVR ?0.2V to 3.8V
• Rail-to-Rail Output
• ?40°C to +125°C Temperature Range

• Architecture
• Voltage FB
• Number of channels (#)
• 1
• Total supply voltage (Min) (+5V=5, +/-5V=10)
• 2.7
• Total supply voltage (Max) (+5V=5, +/-5V=10)
• 11
• GBW (Typ) (MHz)
• 135
• BW @ Acl (MHz)
• 365
• Acl, min spec gain (V/V)
• 1
• Slew rate (Typ) (V/us)
• 460
• Vn at flatband (Typ) (nV/rtHz)
• 10
• Vn at 1 kHz (Typ) (nV/rtHz)
• 10
• Iq per channel (Typ) (mA)
• 3.3
• Vos (offset voltage @ 25 C) (Max) (mV)
• 1.5
• Rail-to-rail
• In to V-, Out
• Features
• Shutdown
• Rating
• Catalog
• Operating temperature range (C)
• -40 to 125
• CMRR (Typ) (dB)
• 98
• Input bias current (Max) (pA)
• 10100000
• Offset drift (Typ) (uV/C)
• 4
• Output current (Typ) (mA)
• 120
• 2nd harmonic (dBc)
• 82
• 3rd harmonic (dBc)
• 80
• @ MHz
• 5

LMH6611的完整型号有：LMH6611MK/NOPB、LMH6611MKE/NOPB、LMH6611MKX/NOPB，以下是这些产品的关键参数及官网采购报价：

LMH6611MK/NOPB，工作温度：-40 to 125，封装：SOT-23-THIN (DDC)-6，包装数量MPQ：1000个，MSL 等级/回流焊峰值温度：Level-1-260C-UNLIM，引脚镀层/焊球材料：SN，TI官网LMH6611MK/NOPB的批量USD价格：.85（1000+）

LMH6611MKE/NOPB，工作温度：-40 to 125，封装：SOT-23-THIN (DDC)-6，包装数量MPQ：250个，MSL 等级/回流焊峰值温度：Level-1-260C-UNLIM，引脚镀层/焊球材料：SN，TI官网LMH6611MKE/NOPB的批量USD价格：.85（1000+）

LMH6611MKX/NOPB，工作温度：-40 to 125，封装：SOT-23-THIN (DDC)-6，包装数量MPQ：3000个，MSL 等级/回流焊峰值温度：Level-1-260C-UNLIM，引脚镀层/焊球材料：SN，TI官网LMH6611MKX/NOPB的批量USD价格：.708（1000+）

551600083-001 — 用于 LMH6611 和 LMH6618 的单路至单路 ADC 驱动器 PCB（采用 SOT23 封装，未填充）

The ADC driver evaluation boards are designed for use with National Semiconductor's high-speed operational amplifier product portfolio. These evaluation boards can be used as an aid in the design and evaluation of National's ADC Driver product in an application, in addition to being a guide for (...)

LMH730216 — 用于采用 5/6 引脚 SOT-23 封装的高速单路运算放大器的评估板

Texas Instruments offers this unpopulated Evaluation Board to aid in the evaluation and testing of high-speed Op Amps that are offered in the 5-/6-pin SOT-23 package. Resistors, capacitors, or any other surface-mount components can be easily mounted on this board in the desired circuit (...)

LMH6611 PSPICE Model

PSpice for TI 可提供帮助评估模拟电路功能的设计和仿真环境。此功能齐全的设计和仿真套件使用 Cadence 的模拟分析引擎。PSpice for TI 可免费使用，包括业内超大的模型库之一，涵盖我们的模拟和电源产品系列以及精选的模拟行为模型。

借助?PSpice for TI 的设计和仿真环境及其内置的模型库，您可对复杂的混合信号设计进行仿真。创建完整的终端设备设计和原型解决方案，然后再进行布局和制造，可缩短产品上市时间并降低开发成本。

在?PSpice for TI 设计和仿真工具中，您可以搜索 TI (...)

TINA-TI — 基于 SPICE 的模拟仿真程序

TINA-TI 提供了 SPICE 所有的传统直流、瞬态和频域分析以及更多。TINA 具有广泛的后处理功能，允许您按照希望的方式设置结果的格式。虚拟仪器允许您选择输入波形、探针电路节点电压和波形。TINA 的原理图捕获非常直观 - 真正的“快速入门”。

TINA-TI 安装需要大约 500MB。直接安装，如果想卸载也很容易。我们相信您肯定会爱不释手。

TINA 是德州仪器 (TI) 专有的 DesignSoft 产品。该免费版本具有完整的功能，但不支持完整版 TINA 所提供的某些其他功能。

如需获取可用 TINA-TI 模型的完整列表，请参阅：SpiceRack - 完整列表

需要 HSpice (...)

ANALOG-ENGINEER-CALC — 模拟工程师计算器

模拟工程师计算器旨在加快模拟电路设计工程师经常使用的许多重复性计算。该基于 PC 的工具提供图形界面，其中显示各种常见计算的列表（从使用反馈电阻器设置运算放大器增益到为稳定模数转换器 (ADC) 驱动器缓冲器电路选择合适的电路设计元件）。除了可用作单独的工具之外，该计算器还能够很好地与模拟工程师口袋参考书中所述的概念配合使用。 lock = 需要出口许可（1分钟）

VOLT-DIVIDER-CALC — 分压器确定一组分压电阻

VOLT-DIVIDER-CALC quickly determines a set of resistors for a voltage divider. This KnowledgeBase Javascript utility can be used to find a set of resistors for a voltage divider to achieve the desired output voltage. This calculator can also be used to design non-inverting attentuation circuits.

(...)