The LMH6645 (single) and LMH6646 (dual), rail-to-rail input and output voltage feedback amplifiers, offer high speed (55 MHz), and low voltage operation (2.7 V) in addition to micro-power shutdown capability (LMH6647, single).

Input common mode voltage range exceeds either supply by 0.3 V, enhancing ease of use in multitude of applications where previously only inferior devices could be used. Output voltage range extends to within 20 mV of either supply rails, allowing wide dynamic range especially in low voltage applications. Even with low supply current of 650 µA/amplifier, output current capability is kept at a respectable ±20 mA for driving heavier loads. Important device parameters such as BW, Slew Rate and output current are kept relatively independent of the operating supply voltage by a combination of process enhancements and design architecture.

In portable applications, the LMH6647 provides shutdown capability while keeping the turn-off current to less than 50 µA. Both turn-on and turn-off characteristics are well behaved with minimal output fluctuations during transitions. This allows the part to be used in power saving mode, as well as multiplexing applications. Miniature packages (SOT-23, VSSOP-8, and SOIC-8) are further means to ease the adoption of these low power high speed devices in applications where board area is at a premium.

• (VS = 2.7V, TA = 25°C, RL = 1kΩ to V+/2, AV = +1. Typical Values Unless Specified.
• ?3dB BW 55 MHz
• Supply Voltage Range 2.5 V to 12 V
• Slew Rate 22 V/μs
• Supply Current 650 μA/channel
• Output Short Circuit Current 42 mA
• Linear Output Current ±20 mA
• Input Common Mode Voltage 0.3 V Beyond Rails
• Output Voltage Swing 20 mV from Rails
• Input Voltage Noise 17 nV/√Hz
• Input Current Noise 0.75 pA/√Hz

• Architecture
• Voltage FB
• Number of channels (#)
• 1
• Total supply voltage (Min) (+5V=5, +/-5V=10)
• 2.5
• Total supply voltage (Max) (+5V=5, +/-5V=10)
• 12
• GBW (Typ) (MHz)
• 40
• BW @ Acl (MHz)
• 55
• Acl, min spec gain (V/V)
• 1
• Slew rate (Typ) (V/us)
• 22
• Vn at flatband (Typ) (nV/rtHz)
• 17
• Vn at 1 kHz (Typ) (nV/rtHz)
• 17
• Iq per channel (Typ) (mA)
• 0.725
• Vos (offset voltage @ 25 C) (Max) (mV)
• 3
• Rail-to-rail
• In, Out
• Rating
• Catalog
• Operating temperature range (C)
• -40 to 85
• CMRR (Typ) (dB)
• 84
• Input bias current (Max) (pA)
• 2000000
• Offset drift (Typ) (uV/C)
• 5
• Output current (Typ) (mA)
• 20
• 2nd harmonic (dBc)
• 62
• 3rd harmonic (dBc)
• 72
• @ MHz
• 1

LMH6645的完整型号有：LMH6645MA/NOPB、LMH6645MAX/NOPB、LMH6645MF/NOPB、LMH6645MFX/NOPB，以下是这些产品的关键参数及官网采购报价：

LMH6645MA/NOPB，工作温度：-40 to 85，封装：SOIC (D)-8，包装数量MPQ：95个，MSL 等级/回流焊峰值温度：Level-1-260C-UNLIM，引脚镀层/焊球材料：SN，TI官网LMH6645MA/NOPB的批量USD价格：.935（1000+）

LMH6645MAX/NOPB，工作温度：-40 to 85，封装：SOIC (D)-8，包装数量MPQ：2500个，MSL 等级/回流焊峰值温度：Level-1-260C-UNLIM，引脚镀层/焊球材料：SN，TI官网LMH6645MAX/NOPB的批量USD价格：.779（1000+）

LMH6645MF/NOPB，工作温度：-40 to 85，封装：SOT-23 (DBV)-5，包装数量MPQ：1000个，MSL 等级/回流焊峰值温度：Level-1-260C-UNLIM，引脚镀层/焊球材料：SN，TI官网LMH6645MF/NOPB的批量USD价格：.935（1000+）

LMH6645MFX/NOPB，工作温度：-40 to 85，封装：SOT-23 (DBV)-5，包装数量MPQ：3000个，MSL 等级/回流焊峰值温度：Level-1-260C-UNLIM，引脚镀层/焊球材料：SN，TI官网LMH6645MFX/NOPB的批量USD价格：.779（1000+）

LMH730216 — 用于采用 5/6 引脚 SOT-23 封装的高速单路运算放大器的评估板

Texas Instruments offers this unpopulated Evaluation Board to aid in the evaluation and testing of high-speed Op Amps that are offered in the 5-/6-pin SOT-23 package. Resistors, capacitors, or any other surface-mount components can be easily mounted on this board in the desired circuit (...)

LMH730227 — 用于采用 8 引脚 SOIC 封装的高速单路运算放大器的评估板

National Semiconductor offers this unpopulated Evaluation Board to aid in the evaluation and testing of high-speed Op Amp that are offered in the 8-Pin SOIC package. Resistors, capacitors, or any other surface-mount components can be easily mounted on this board in the desired circuit (...)

LMH6645 PSPICE Model

PSpice for TI 可提供帮助评估模拟电路功能的设计和仿真环境。此功能齐全的设计和仿真套件使用 Cadence 的模拟分析引擎。PSpice for TI 可免费使用，包括业内超大的模型库之一，涵盖我们的模拟和电源产品系列以及精选的模拟行为模型。

借助?PSpice for TI 的设计和仿真环境及其内置的模型库，您可对复杂的混合信号设计进行仿真。创建完整的终端设备设计和原型解决方案，然后再进行布局和制造，可缩短产品上市时间并降低开发成本。

在?PSpice for TI 设计和仿真工具中，您可以搜索 TI (...)

TINA-TI — 基于 SPICE 的模拟仿真程序

TINA-TI 提供了 SPICE 所有的传统直流、瞬态和频域分析以及更多。TINA 具有广泛的后处理功能，允许您按照希望的方式设置结果的格式。虚拟仪器允许您选择输入波形、探针电路节点电压和波形。TINA 的原理图捕获非常直观 - 真正的“快速入门”。

TINA-TI 安装需要大约 500MB。直接安装，如果想卸载也很容易。我们相信您肯定会爱不释手。

TINA 是德州仪器 (TI) 专有的 DesignSoft 产品。该免费版本具有完整的功能，但不支持完整版 TINA 所提供的某些其他功能。

如需获取可用 TINA-TI 模型的完整列表，请参阅：SpiceRack - 完整列表

需要 HSpice (...)

ANALOG-ENGINEER-CALC — 模拟工程师计算器

模拟工程师计算器旨在加快模拟电路设计工程师经常使用的许多重复性计算。该基于 PC 的工具提供图形界面，其中显示各种常见计算的列表（从使用反馈电阻器设置运算放大器增益到为稳定模数转换器 (ADC) 驱动器缓冲器电路选择合适的电路设计元件）。除了可用作单独的工具之外，该计算器还能够很好地与模拟工程师口袋参考书中所述的概念配合使用。 lock = 需要出口许可（1分钟）

VOLT-DIVIDER-CALC — 分压器确定一组分压电阻

VOLT-DIVIDER-CALC quickly determines a set of resistors for a voltage divider. This KnowledgeBase Javascript utility can be used to find a set of resistors for a voltage divider to achieve the desired output voltage. This calculator can also be used to design non-inverting attentuation circuits.

(...)