The LP38855 is a high-current, fast-response regulator which can maintain output voltage regulation with an extremely low input to output voltage drop. Fabricated on a CMOS process, the device operates from two input voltages: V_BIAS provides power for the internal bias and control circuits, as well as drive for the gate of the N-MOS power transistor, while V_IN supplies power to the load. The use of an external bias rail allows the part to operate from ultra low V_IN voltages. Unlike bipolar regulators, the CMOS architecture consumes extremely low quiescent current at any output load current. The use of an N-MOS power transistor results in wide bandwidth, yet minimum external capacitance is required to maintain loop stability.

The fast transient response of this device makes it suitable for use in powering DSP, Microcontroller Core voltages and Switch Mode Power Supply post regulators. The LP38855 is available in TO-220 and DDPAK/TO-263 5-Lead packages.

Dropout Voltage: 130 mV (typical) at 1.5A load current.

Low Ground Pin Current: 10 mA (typical) at 1.5A load current.

Shutdown Current: 1 µA (typical) I_IN(GND) when EN pin is low.

Precision Output Voltage: ±1.0% for T_J = 25°C and ±2.0% for 0°C ≤ T_J ≤ +125°C, across all line and load conditions

• Standard VOUT Values of 0.8V and 1.2V
• Wide VBIAS Supply Operating Range of 3.0V to 5.5V
• Stable with 10 μF Ceramic Capacitors
• Dropout Voltage of 130 mV (Typical) at 1.5A Load Current
• Precision Output Voltage Across All Line and Load Conditions:
  • ±1.0% for TJ = 25°C
  • ±2.0% for 0°C ≤ TJ ≤ +125°C
  • ±3.0% for -40°C ≤ TJ ≤ +125°C
• Over-Temperature and Over-Current Protection
• Available in 5 Lead TO-220 and DDPAK/TO-263 Packages
• Custom VOUT Values between 0.8V and 1.2V are Available
• -40°C to +125°C Operating Temperature Range

All trademarks are the property of their respective owners.

• Output options
• Fixed Output
• Iout (Max) (A)
• 1.5
• Vin (Max) (V)
• 5.5
• Vin (Min) (V)
• 0.98
• Vout (Max) (V)
• 1.2
• Vout (Min) (V)
• 0.8
• Fixed output options (V)
• 0.8, 1.2
• Noise (uVrms)
• 150
• Iq (Typ) (mA)
• 10
• Thermal resistance θJA (°C/W)
• 60
• Rating
• Catalog
• Load capacitance (Min) (μF)
• 10
• Regulated outputs (#)
• 1
• Features
• Enable
• Accuracy (%)
• 2
• PSRR @ 100 KHz (dB)
• 37
• Dropout voltage (Vdo) (Typ) (mV)
• 130
• Operating temperature range (C)
• -40 to 125

LP38855的完整型号有：LP38855S-1.2/NOPB、LP38855SX-1.2/NOPB、LP38855T-0.8/NOPB、LP38855T-1.2/NOPB、LP38855S-1.2，以下是这些产品的关键参数及官网采购报价：

LP38855S-1.2/NOPB，工作温度：-40 to 125，封装：DDPAK/TO-263 (KTT)-5，包装数量MPQ：45个，MSL 等级/回流焊峰值温度：Level-3-245C-168 HR，引脚镀层/焊球材料：SN，TI官网LP38855S-1.2/NOPB的批量USD价格：1.122（1000+）

LP38855SX-1.2/NOPB，工作温度：-40 to 125，封装：DDPAK/TO-263 (KTT)-5，包装数量MPQ：500个，MSL 等级/回流焊峰值温度：Level-3-245C-168 HR，引脚镀层/焊球材料：SN，TI官网LP38855SX-1.2/NOPB的批量USD价格：.935（1000+）

LP38855T-0.8/NOPB，工作温度：-40 to 125，封装：TO-220 (NDH)-5，包装数量MPQ：45个，MSL 等级/回流焊峰值温度：Level-1-NA-UNLIM，引脚镀层/焊球材料：SN，TI官网LP38855T-0.8/NOPB的批量USD价格：.935（1000+）

LP38855T-1.2/NOPB，工作温度：-40 to 125，封装：TO-220 (NDH)-5，包装数量MPQ：45个，MSL 等级/回流焊峰值温度：Level-1-NA-UNLIM，引脚镀层/焊球材料：SN，TI官网LP38855T-1.2/NOPB的批量USD价格：.935（1000+）

LP38855S-1.2，工作温度：-40 to 125，封装：DDPAK/TO-263 (KTT)-5，包装数量MPQ：45个，MSL 等级/回流焊峰值温度：Level-3-235C-168 HR，引脚镀层/焊球材料：SNPB，TI官网LP38855S-1.2的批量USD价格：1.449（1000+）

PMP9335 — 面向 Xilinx Zynq FPGA 应用的多输出、多路降压 20W 电源参考设计

PMP9335 专为使用 TPS84A20 和 TPS84320 的 Xilinx Zynq FPGA 应用而设计。此设计使用外部计时器将开关频率同步到 300 kHz。它还采用受控的加电和断电序列。