The LP8545 is a white LED driver with integrated boost converter. It has six adjustable current sinks which can be controlled by PWM input or with I²C-compatible serial interface.

The boost converter has adaptive output voltage control based on the LED driver voltages. This feature minimizes the power consumption by adjusting the voltage to lowest sufficient level in all conditions.

LED outputs have 8-bit current resolution and up to 13-bit PWM resolution with additional 1-3 bit dithering to achieve smooth and precise brightness control. Proprietary Phase Shift PWM control is used for LED outputs to reduce peak current from the boost converter, thus making the boost capacitors smaller. The Phase Shifting scheme also eliminates audible noise.

Internal EEPROM is used for storing the configuration data. This makes it possible to have minimum external component count and make the solution very small.

LP8545 has safety features which make it possible to detect LED outputs with open or short fault. As well low input voltage and boost over-current conditions are monitored and chip is turned off in case of these events. Thermal de-rating function prevents overheating of the device by reducing backlight brightness when set temperature has been reached.

LP8545 is available in TI’s WQFN 24-pin package.

• High-Voltage DC/DC Boost Converter with Integrated FET with Four Switching Frequency Options: 156/312/625/1250 kHz
• Configurable for Use with External FET for Applications Needing Higher Output Voltage
• 2.7V – 22V Input Voltage Range to Support 1x…5x Cell Li-Ion Batteries
• Programmable PWM Resolution
  • 8 to 13 True Bit (Steady State)
  • Additional 1 to 3 Bits Using Dithering During Brightness Changes
• I2C and PWM Brightness Control
• PWM Output Frequency and LED Current Set Through Resistors
• Optional Synchronization to Display VSYNC Signal
• 6 LED Outputs with LED fault (Short/Open) Detection
• Low Input Voltage, Over-Temperature, Over-Current Detection and Shutdown
• Minimum Number of External Components
• WQFN 24-Pin Package, 4 × 4 × 0.8 mm

• Number of channels (#)
• 6
• Vin (Min) (V)
• 5.5
• Vin (Max) (V)
• 22
• Vout (Min) (V)
• 0
• Vout (Max) (V)
• 55
• Type
• Inductive
• Switching frequency (Max) (kHz)
• 1250
• LED current per channel (mA)
• 50
• Peak efficiency (%)
• 91
• Topology
• Boost
• Features
• Adjustable Switch Frequency, Enable/Shutdown, I2C Control, PWM Control
• Operating temperature range (C)
• -30 to 85

LP8545的完整型号有：LP8545SQ/NOPB、LP8545SQE/NOPB、LP8545SQX/NOPB，以下是这些产品的关键参数及官网采购报价：

LP8545SQ/NOPB，工作温度：PropertyValue，封装：WQFN (RTW)-24，包装数量MPQ：1000个，MSL 等级/回流焊峰值温度：Level-1-260C-UNLIM，引脚镀层/焊球材料：SN，TI官网LP8545SQ/NOPB的批量USD价格：1.098（1000+）

LP8545SQE/NOPB，工作温度：-30 to 85，封装：WQFN (RTW)-24，包装数量MPQ：250个，MSL 等级/回流焊峰值温度：Level-1-260C-UNLIM，引脚镀层/焊球材料：SN，TI官网LP8545SQE/NOPB的批量USD价格：1.098（1000+）

LP8545SQX/NOPB，工作温度：-30 to 85，封装：WQFN (RTW)-24，包装数量MPQ：4500个，MSL 等级/回流焊峰值温度：Level-1-260C-UNLIM，引脚镀层/焊球材料：SN，TI官网LP8545SQX/NOPB的批量USD价格：.915（1000+）

PSPICE-FOR-TI — 适用于 TI 设计和模拟工具的 PSpice

PSpice for TI 可提供帮助评估模拟电路功能的设计和仿真环境。此功能齐全的设计和仿真套件使用 Cadence 的模拟分析引擎。PSpice for TI 可免费使用，包括业内超大的模型库之一，涵盖我们的模拟和电源产品系列以及精选的模拟行为模型。

借助?PSpice for TI 的设计和仿真环境及其内置的模型库，您可对复杂的混合信号设计进行仿真。创建完整的终端设备设计和原型解决方案，然后再进行布局和制造，可缩短产品上市时间并降低开发成本。

在?PSpice for TI 设计和仿真工具中，您可以搜索 TI (...)