The SN65HVD96 is specifically designed to meet the requirements for a transceiver which operates with no errors if the twisted-pair signal wires are connected normally or reversed. This allows for error free operation in applications where the signal wires may become inadvertently reversed during installation or maintenance. This feature is corrected internally so no intervention from the controller or operator is required. The SN65HVD96 complies with the requirements of ANSI/TIA-4963, Electrical Characteristics of Reversible Balanced Voltage Digital Interface Circuits.

Similar to RS-485, these transceivers can be used for point-to-point, multi-drop, or multi-point networks. Sympol devices are not backwards compatible with, but are an upgrade to, existing RS-485 networks. The pin-out is identical to the industry-standard SN75176 transceiver, allowing direct upgrade from RS-485 to SymPol. Current-limited differential outputs protect in case of driver contention on a party-line bus. High receiver input impedance allows connection of at least 32 nodes. Several fault tolerant features are integrated into the device to protect from operational hazards. Current limiting on the driver outputs protects against short-circuit faults, and operates independently on each driver output. An automatic thermal shutdown protects the driver circuits against over temperature conditions. The receiver output enters a deterministic failsafe state if the bus connection is left disconnected or if the bus wires are shorted together.

The small outline integrated circuit (SOIC) package saves board space compared to equivalent discrete implementations. These devices are fully characterized for operation over the industrial temperature range of –40°C to 85°C.

• Communicate Without Errors on Normal or Reversed-Wire Bus Lines
• Up to 5 Mbps Signaling
• Industrial Temperature Range: –40°C to 85°C
• Symmetric Polarity Receiver
• Receiver Hysteresis > 100 mV
• Connect up to 32 Nodes Plus Parallel Terminators on one Bus, or Connect up to 200 Nodes on an Unterminated Bus
• Transient Protection
  • ±12 kV Human Body Model on Bus Pins
  • ±25 V Repetitive Transient Pulse on Bus Pins
• Additional Reliability Features:
  • Bus Standoff From –35 V to 40 V
  • Driver Output Short-Circuit Current Limit
  • Automatic Thermal Shutdown and Recovery
• Complies with ANSI/TIA-4963 Standard

• Number of receivers
• 1
• Number of transmitters
• 1
• Duplex
• Half
• Supply voltage (Nom) (V)
• 5
• Signaling rate (Max) (Mbps)
• 5
• IEC 61000-4-2 contact (+/- kV)
• —
• Fault protection (V)
• -35 to 40
• Common mode range
• -7 to 12
• Number of nodes
• 32
• Isolated
• No
• ICC (Max) (mA)
• 20
• Rating
• Catalog
• Operating temperature range (C)
• -40 to 85

SN65HVD96的完整型号有：SN65HVD96D、SN65HVD96DR，以下是这些产品的关键参数及官网采购报价：

SN65HVD96D，工作温度：-40 to 85，封装：SOIC (D)-8，包装数量MPQ：75个，MSL 等级/回流焊峰值温度：Level-1-260C-UNLIM，引脚镀层/焊球材料：NIPDAU，TI官网SN65HVD96D的批量USD价格：1.457（1000+）

SN65HVD96DR，工作温度：-40 to 85，封装：SOIC (D)-8，包装数量MPQ：2500个，MSL 等级/回流焊峰值温度：Level-1-260C-UNLIM，引脚镀层/焊球材料：NIPDAU，TI官网SN65HVD96DR的批量USD价格：1.214（1000+）

SN65HVD96EVM — 用于 SN65HVD96 的评估模块

此 EVM 使设计人员可以评估 TI SymPol 收发器器件。可以用总线终端块连接多个电路板以模拟简单的总线系统设计。

PSPICE-FOR-TI — 适用于 TI 设计和模拟工具的 PSpice

PSpice for TI 可提供帮助评估模拟电路功能的设计和仿真环境。此功能齐全的设计和仿真套件使用 Cadence 的模拟分析引擎。PSpice for TI 可免费使用，包括业内超大的模型库之一，涵盖我们的模拟和电源产品系列以及精选的模拟行为模型。

借助?PSpice for TI 的设计和仿真环境及其内置的模型库，您可对复杂的混合信号设计进行仿真。创建完整的终端设备设计和原型解决方案，然后再进行布局和制造，可缩短产品上市时间并降低开发成本。

在?PSpice for TI 设计和仿真工具中，您可以搜索 TI (...)

TINA-TI — 基于 SPICE 的模拟仿真程序

TINA-TI 提供了 SPICE 所有的传统直流、瞬态和频域分析以及更多。TINA 具有广泛的后处理功能，允许您按照希望的方式设置结果的格式。虚拟仪器允许您选择输入波形、探针电路节点电压和波形。TINA 的原理图捕获非常直观 - 真正的“快速入门”。

TINA-TI 安装需要大约 500MB。直接安装，如果想卸载也很容易。我们相信您肯定会爱不释手。

TINA 是德州仪器 (TI) 专有的 DesignSoft 产品。该免费版本具有完整的功能，但不支持完整版 TINA 所提供的某些其他功能。

如需获取可用 TINA-TI 模型的完整列表，请参阅：SpiceRack - 完整列表

需要 HSpice (...)

TIDA-01171 — 交流耦合 RS-485 参考设计

TIDA-01171 参考设计可在交流耦合链路上实现 RS-485 通信，即便是在较低数据速率下仍然可行。即使节点之间存在巨大的接地电势差，仍可实现节点通信。采用交流耦合还有助于为收发器提供总线故障保护，总线故障可能会导致高电压电源发生直接短路。

TIDA-00862 — RS-485 双线制全双工参考设计

The design enables full duplex RS-485 communications over a single pair of conductors rather than four by utilizing bus contention. By adding small-valued serial resistors to the bus lines to limit currents, a tri-stated differential bus is allowed and the SN65HVD96 SymPol transciver can be used (...)