These 18-bit universal bus transceivers combine D-type latches and D-type flip-flops to allow data flow in transparent, latched, and clocked modes. Data flow in each direction is controlled by output-enable (OEAB and OEBA\), latch-enable (LEAB and LEBA), and clock (CLKAB\ and CLKBA\) inputs.

For A-to-B data flow, the device operates in the transparent mode when LEAB is high. When LEAB is low, the A data is latched if CLKAB\ is held at a high or low logic level. If LEAB is low, the A data is stored in the latch/flip-flop on the high-to-low transition of CLKAB\. Output-enable OEAB is active high. When OEAB is high, the outputs are active. When OEAB is low, the outputs are in the high-impedance state.

Data flow for B to A is similar to that of A to B but uses OEBA\, LEBA, and CLKBA\. The output enables are complementary (OEAB is active high and OEBA\ is active low).

The B-port outputs, which are designed to source or sink up to 12 mA, include equivalent 25- series resistors to reduce overshoot and undershoot.

When V_CC is between 0 and 2.1 V, the device is in the high-impedance state during power up or power down. However, to ensure the high-impedance state above 2.1 V, OE\ should be tied to V_CC through a pullup resistor and OE should be tied to GND through a pulldown resistor; the minimum value of the resistor is determined by the current-sinking/current-sourcing capability of the driver.

The SN54ABT162500 is characterized for operation over the full military temperature range of -55°C to 125°C. The SN74ABT162500 is characterized for operation from -40°C to 85°C.

A-to-B data flow is shown: B-to-A flow is similar but uses OEBA\, LEBA, and CLKBA\.

Output level before the indicated steady-state input conditions were established

^§ Output level before the indicated steady-state input conditions were established, provided that CLKAB\ was low before LEAB went low

• Members of the Texas Instruments WidebusTM Family
• B-Port Outputs Have Equivalent 25- Series Resistors, So No External Resistors Are Required
• State-of-the-Art EPIC-II BTM BiCMOS Design Significantly Reduces Power Dissipation
• UBTTM (Universal Bus Transceiver) Combines D-Type Latches and D-Type Flip-Flops for Operation in Transparent, Latched, or Clocked Mode
• Typical VOLP (Output Ground Bounce) < 0.8 V at VCC = 5 V, TA = 25°C
• High-Impedance State During Power Up and Power Down
• Flow-Through Architecture Optimizes PCB Layout
• Latch-Up Performance Exceeds 500 mA Per JESD 17
• ESD Protection Exceeds 2000 V Per MIL-STD-883, Method 3015; Exceeds 200 V Using Machine Model (C = 200 pF, R = 0)
• Package Options Include Plastic Shrink Small-Outline (DL) Package and 380-mil Fine-Pitch Ceramic Flat (WD) Package Using 25-mil Center-to-Center Spacings

  Widebus, EPIC-IIB, and UBT are trademarks of Texas Instruments Incorporated.

• IOL (Max) (mA)
• 64
• IOH (Max) (mA)
• -32
• Technology Family
• ABT
• Rating
• Catalog
• Operating temperature range (C)
• -40 to 85

SN74ABT162500的完整型号有：SN74ABT162500DL，以下是这些产品的关键参数及官网采购报价：

SN74ABT162500DL，工作温度：-40 to 85，封装：SSOP (DL)-56，包装数量MPQ：20个，MSL 等级/回流焊峰值温度：Level-1-260C-UNLIM，引脚镀层/焊球材料：NIPDAU，TI官网SN74ABT162500DL的批量USD价格：2.278（1000+）

SN74ABT162500DL，工作温度：-40 to 85，封装：SSOP (DL)-56，包装数量MPQ：20个，MSL 等级/回流焊峰值温度：Level-1-260C-UNLIM，引脚镀层/焊球材料：NIPDAU，TI官网SN74ABT162500DL的批量USD价格：2.278（1000+）