- 制造厂商:TI
- 产品类别:逻辑和电压转换
- 技术类目:触发器、锁存器和寄存器 - D 型锁存器
- 功能描述:具有三态输出的增强型产品 16 位 D 类透明锁存器
- 点击这里打开及下载SN74ABT16373A-EP的技术文档资料
- TI代理渠道,提供当日发货、严格的质量标准,满足您的目标价格
The SN74ABT16373A-EP is a 16-bit transparent D-type latch with 3-state outputs designed specifically for driving highly capacitive or relatively low-impedance loads. The SN74ABT16373A-EP is particularly suitable for implementing buffer registers, I/O ports, bidirectional bus drivers, and working registers.
The SN74ABT16373A-EP can be used as two 8-bit latches or one 16-bit latch. When the latch-enable (LE) input is high, the Q outputs follow the data (D) inputs. When LE is taken low, the Q outputs are latched at the levels set up at the D inputs.
A buffered output-enable (OE) input can be used to place the eight outputs in either a normal logic state (high or low logic levels) or a high-impedance state. In the high-impedance state, the outputs neither load nor drive the bus lines significantly. The high-impedance state and the increased drive provide the capability to drive bus lines without need for interface or pullup components.
OE does not affect internal operations of the latch. Old data can be retained or new data can be entered while the outputs are in the high-impedance state.
When VCC is between 0 and 2.1 V, the device is in the high-impedance state during power up or power down. However, to ensure the high-impedance state above 2.1 V, OE should be tied to VCC through a pullup resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver.
The SN74ABT16373A-EP is characterized for operation from -55°C to 125°C.
- Controlled Baseline
- One Assembly/Test Site, One Fabrication Site
- Extended Temperature Performance of -55°C to 125°C
- Enhanced Diminishing Manufacturing Sources (DMS) Support
- Enhanced Product Change Notification
- Qualification Pedigree(1)
- Member of the Texas Instruments Widebus? Family
- State-of-the-Art EPIC-IIB? BiCMOS Design Significantly Reduces Power Dissipation
- Latch-Up Performance Exceeds 500 mA Per JEDEC Standard JESD-17
- Typical VOLP (Output Ground Bounce) <0.8 V at VCC = 5 V, TA = 25°C
- High-Impedance State During Power Up and Power Down
- Distributed VCC and GND Pin Configuration Minimizes High-Speed Switching Noise
- Flow-Through Architecture Optimizes PCB Layout
- High-Drive Outputs (-24-mA IOH, 48-mA IOL)
- Plastic 300-mil Shrink Small-Outline (DL) Package
(1)Component qualification in accordance with JEDEC and industry standards to ensure reliable operation over an extended temperature range. This includes, but is not limited to, Highly Accelerated Stress Test (HAST) or biased 85/85, temperature cycle, autoclave or unbiased HAST, electromigration, bond intermetallic life, and mold-compound life. Such qualification testing should not be viewed as justifying use of this component beyond specified performance and environmental limits.
Widebus, EPIC-IIB are trademarks of Texas Instruments.- Number of channels (#)
- 16
- Technology Family
- ABT
- Supply voltage (Min) (V)
- 4.5
- Supply voltage (Max) (V)
- 5.5
- Input type
- TTL-Compatible CMOS
- Output type
- 3-State
- Clock Frequency (Max) (MHz)
- 150
- IOL (Max) (mA)
- 64
- IOH (Max) (mA)
- -32
- ICC (Max) (uA)
- 85000
- Features
- Very high speed (tpd 5-10ns), Partial power down (Ioff), Power up 3-state, Flow-through pinout
SN74ABT16373A-EP的完整型号有:CABT16373AMDLREP、V62/06628-01XE,以下是这些产品的关键参数及官网采购报价:
CABT16373AMDLREP,工作温度:-55 to 125,封装:SSOP (DL)-48,包装数量MPQ:1000个,MSL 等级/回流焊峰值温度:Level-1-260C-UNLIM,引脚镀层/焊球材料:NIPDAU,TI官网CABT16373AMDLREP的批量USD价格:1.781(1000+)
V62/06628-01XE,工作温度:-55 to 125,封装:SSOP (DL)-48,包装数量MPQ:1000个,MSL 等级/回流焊峰值温度:Level-1-260C-UNLIM,引脚镀层/焊球材料:NIPDAU,TI官网V62/06628-01XE的批量USD价格:1.781(1000+)
CABT16373AMDLREP,工作温度:-55 to 125,封装:SSOP (DL)-48,包装数量MPQ:1000个,MSL 等级/回流焊峰值温度:Level-1-260C-UNLIM,引脚镀层/焊球材料:NIPDAU,TI官网CABT16373AMDLREP的批量USD价格:1.781(1000+)
V62/06628-01XE,工作温度:-55 to 125,封装:SSOP (DL)-48,包装数量MPQ:1000个,MSL 等级/回流焊峰值温度:Level-1-260C-UNLIM,引脚镀层/焊球材料:NIPDAU,TI官网V62/06628-01XE的批量USD价格:1.781(1000+)