The SN74AXCH2T45 is a two-bit non-inverting bus transceiver that uses two individually configurable power-supply rails. The device is operational with both V_CCA and V_CCB supplies as low as 0.65 V. The A port is designed to track V_CCA, which accepts any supply voltage from 0.65 V to 3.6 V. The B port is designed to track V_CCB, which also accepts any supply voltage from 0.65 V to 3.6 V. Additionally the SN74AXCH2T45 is compatible with a single-supply system.

The SN74AXCH2T45 device is designed for asynchronous communication between data buses. The device transmits data from the A bus to the B bus or from the B bus to the A bus, depending on the logic level of the direction-control input (DIR). The SN74AXCH2T45 device is designed so the control pin (DIR) is referenced to V_CCA.

Active bus-hold circuitry holds unused or undriven inputs at a valid logic state. Use of pullup or pulldown resistors with the bus-hold circuitry is not recommended. If a supply is present for VCCA or VCCB, the bus-hold circuitry always remains active on the A or B inputs respectively, independent of the state of the direction control pin.

This device is fully specified for partial-power-down applications using the I_off current. The I_off protection circuitry ensures that no excessive current is drawn from or to an input, output, or combined I/O that is biased to a specific voltage while the device is powered down.

The V_CC isolation feature ensures that if either V_CCA or V_CCB is less than 100 mV, both I/O ports enter a high-impedance state by disabling their outputs.

Glitch-free power supply sequencing allows either supply rail to be powered on or off in any order while providing robust power sequencing performance.

• Fully configurable dual-rail design allows each port to operate with a power supply range from 0.65 V to 3.6 V
• Operating temperature from –40°C to +125°C
• Glitch-free power supply sequencing
• Up to 380 Mbps support when translating from 1.8 V to 3.3 V
• VCC isolation feature
  • If either VCC input is below 100 mV, all I/O outputs are disabled and become high impedance
• Ioff supports partial-power-down mode operation
• Compatible with AVC family level shifters
• Latch-up performance exceeds 100 mA per JESD 78, Class II
• ESD protection exceeds JESD 22
  • 8000-V human-body model (HBM)
  • 1000-V charged-device model (CDM)

• Technology Family
• AXC
• Applications
• UART, JTAG
• Bits (#)
• 2
• High input voltage (Min) (Vih)
• 0.45
• High input voltage (Max) (Vih)
• 3.6
• Vout (Min) (V)
• 0.65
• Vout (Max) (V)
• 3.6
• IOH (Max) (mA)
• -12
• IOL (Max) (mA)
• 12
• Rating
• Catalog

SN74AXCH2T45的完整型号有：SN74AXCH2T45DCUR、SN74AXCH2T45DTMR，以下是这些产品的关键参数及官网采购报价：

SN74AXCH2T45DCUR，工作温度：-40 to 125，封装：VSSOP (DCU)-8，包装数量MPQ：3000个，MSL 等级/回流焊峰值温度：Level-1-260C-UNLIM，引脚镀层/焊球材料：SN，TI官网SN74AXCH2T45DCUR的批量USD价格：.2（1000+）

SN74AXCH2T45DTMR，工作温度：-40 to 125，封装：X2SON (DTM)-8，包装数量MPQ：5000个，MSL 等级/回流焊峰值温度：Level-1-260C-UNLIM，引脚镀层/焊球材料：NIPDAUAG，TI官网SN74AXCH2T45DTMR的批量USD价格：.21（1000+）

5-8-LOGIC-EVM — 支持 5 至 8 引脚 DCK、DCT、DCU、DRL 和 DBV 封装的通用逻辑 EVM

灵活的 EVM 设计用于支持具有 5 至 8 引脚数且采用 DCK、DCT、DCU、DRL 或 DBV 封装的任何器件。

AVCLVCDIRCNTRL-EVM — 适用于方向控制双向转换器件、支持 AVC 和 LVC 的通用 EVM

该通用 EVM 旨在支持 1、2、4 和 8 通道 LVC 和 AVC 方向控制转换器件。它还以相同数量的通道支持总线保持和汽车 Q1 器件。AVC 是低电压转换器件，具有 12mA 的较低驱动强度。LVC 是 1.65 至 5.5V 的较高电压转换器件，具有 32mA 的较高驱动强度。

AXC2T-SMALLPKGEVM — AXC2T-SMALLPKGEVM

This EVM is designed to support DTM and RSW packages for the AXC and LVC family of DIR controlled bidirectional devices. The AXC and AVC devices belong to the low voltage direction controlled translation family with operating voltage from 0.65V to 3.6V (AXC) and 1.2 to 3.6 (AVC) with 12mA of drive (...)