The 'GTL16612 devices are 18-bit UBT™ transceivers that provide LVTTL-to-GTL/GTL+ and GTL/GTL+-to-LVTTL signal-level translation. They combine D-type flip-flops and D-type latches to allow for transparent, latched, clocked, and clock-enabled modes of data transfer identical to the '16601 function. The devices provide an interface between cards operating at LVTTL logic levels and a backplane operating at GTL/GTL+ signal levels. Higher-speed operation is a direct result of the reduced output swing (<1 V), reduced input threshold levels, and OEC™ circuitry.

The user has the flexibility of using these devices at either GTL (V_TT = 1.2 V and V_REF = 0.8 V) or the preferred higher noise margin GTL+ (V_TT = 1.5 V and V_REF = 1 V) signal levels. GTL+ is the Texas Instruments derivative of the Gunning Transceiver Logic (GTL) JEDEC standard JESD 8-3. The B port normally operates at GTL or GTL+ signal levels, while the A-port and control inputs are compatible with LVTTL logic levels and are 5-V tolerant. V_REF is the reference input voltage for the B port.

V_CC (5 V) supplies the internal and GTL circuitry while V_CC (3.3 V) supplies the LVTTL output buffers.

Data flow in each direction is controlled by output-enable (OEAB\ and OEBA\), latch-enable(LEAB and LEBA), and clock (CLKAB and CLKBA) inputs. The clock can be controlled by the clock-enable (CEAB\ and CEBA\) inputs. For A-to-B data flow, the devices operate in the transparent mode when LEAB is high. When LEAB is low, the A data is latched if CEAB\ is low and CLKAB is held at a high or low logic level. If LEAB is low, the A data is stored in the latch/flip-flop on the low-to-high transition of CLKAB if CEAB\ also is low. When OEAB\ is low, the outputs are active. When OEAB\ is high, the outputs are in the high-impedance state. Data flow for B to A is similar to that for A to B, but uses OEBA\, LEBA, CLKBA, and CEBA\.

These devices are fully specified for partial-power-down applications using I_off. The I_off circuitry disables the outputs, preventing damaging current backflow through the device when it is powered down.

Active bus-hold circuitry holds unused or undriven LVTTL inputs at a valid logic state. Use of pullup or pulldown resistors with the bus-hold circuitry is not recommended.

• Members of Texas Instruments' Widebus? Family
• UBT? Transceivers Combine D-Type Latches and D-Type Flip-Flops for Operation in Transparent, Latched, Clocked, or Clock-Enabled Modes
• OEC? Circuitry Improves Signal Integrity and Reduces Electromagnetic Interference
• Translate Between GTL/GTL+ Signal Levels and LVTTL Logic Levels
• Support Mixed-Mode (3.3 V and 5 V) Signal Operation on A-Port and Control Inputs
• Identical to \x9216601 Function
• Ioff Supports Partial-Power-Down Mode Operation
• Bus Hold on Data Inputs Eliminates the Need for External Pullup/Pulldown Resistors on A Port
• Distributed VCC and GND Pins Minimize High-Speed Switching Noise
• Latch-Up Performance Exceeds 500 mA Per JESD 17

OEC, UBT, and Widebus are trademarks of Texas Instruments.

• Technology Family
• GTL
• Applications
• GTL
• Rating
• Catalog
• Operating temperature range (C)
• -40 to 85

SN74GTL16612的完整型号有：SN74GTL16612DGGR、SN74GTL16612DL，以下是这些产品的关键参数及官网采购报价：

SN74GTL16612DGGR，工作温度：-40 to 85，封装：TSSOP (DGG)-56，包装数量MPQ：2000个，MSL 等级/回流焊峰值温度：Level-1-260C-UNLIM，引脚镀层/焊球材料：NIPDAU，TI官网SN74GTL16612DGGR的批量USD价格：4.348（1000+）

SN74GTL16612DL，工作温度：-40 to 85，封装：SSOP (DL)-56，包装数量MPQ：20个，MSL 等级/回流焊峰值温度：Level-1-260C-UNLIM，引脚镀层/焊球材料：NIPDAU，TI官网SN74GTL16612DL的批量USD价格：5.435（1000+）

SN74GTL16612DGGR，工作温度：-40 to 85，封装：TSSOP (DGG)-56，包装数量MPQ：2000个，MSL 等级/回流焊峰值温度：Level-1-260C-UNLIM，引脚镀层/焊球材料：NIPDAU，TI官网SN74GTL16612DGGR的批量USD价格：4.348（1000+）

SN74GTL16612DL，工作温度：-40 to 85，封装：SSOP (DL)-56，包装数量MPQ：20个，MSL 等级/回流焊峰值温度：Level-1-260C-UNLIM，引脚镀层/焊球材料：NIPDAU，TI官网SN74GTL16612DL的批量USD价格：5.435（1000+）