These octal buffers/drivers are designed specifically for low-voltage (3.3-V) V_CC operation, but with the capability to provide a TTL interface to a 5-V system environment.

The ’LVTH540 devices are ideal for driving bus lines or buffer memory address registers. These devices feature inputs and outputs on opposite sides of the package that facilitate printed circuit board layout.

The 3-state control gate is a 2-input AND gate with active-low inputs so that if either output-enable (OE1\ or OE2\) input is high, all outputs are in the high-impedance state.

Active bus-hold circuitry holds unused or undriven inputs at a valid logic state. Use of pullup or pulldown resistors with the bus-hold circuitry is not recommended.

When V_CC is between 0 and 1.5 V, the devices are in the high-impedance state during power up or power down. However, to ensure the high-impedance state above 1.5 V, OE\ should be tied to V_CC through a pullup resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver.

These devices are fully specified for hot-insertion applications using I_off and power-up 3-state. The I_off circuitry disables the outputs, preventing damaging current backflow through the devices when they are powered down. The power-up 3-state circuitry places the outputs in the high-impedance state during power up and power down, which prevents driver conflict.

• Support Mixed-Mode Signal Operation (5-V Input and Output Voltages With 3.3-V VCC)
• Typical VOLP (Output Ground Bounce) <0.8 V at VCC = 3.3 V, TA = 25°C
• Support Unregulated Battery Operation Down to 2.7 V
• Ioff and Power-Up 3-State Support Hot Insertion
• Bus Hold on Data Inputs Eliminates the Need for External Pullup/Pulldown Resistors
• Latch-Up Performance Exceeds 500 mA Per JESD 17
• ESD Protection Exceeds JESD 22
  • 2000-V Human-Body Model (A114-A)
  • 200-V Machine Model (A115-A)

• Technology Family
• LVT
• Supply voltage (Min) (V)
• 2.7
• Supply voltage (Max) (V)
• 3.6
• Number of channels (#)
• 8
• IOL (Max) (mA)
• 64
• IOH (Max) (mA)
• -32
• ICC (Max) (uA)
• 5000
• Input type
• TTL-Compatible CMOS
• Output type
• 3-State
• Features
• Ultra high speed (tpd <5ns), Partial power down (Ioff), Over-voltage tolerant inputs, Power up 3-state, Bus-hold
• Rating
• Catalog

SN74LVTH540的完整型号有：SN74LVTH540DBR、SN74LVTH540DW、SN74LVTH540DWR、SN74LVTH540PW、SN74LVTH540PWR，以下是这些产品的关键参数及官网采购报价：

SN74LVTH540DBR，工作温度：-40 to 85，封装：SSOP (DB)-20，包装数量MPQ：2000个，MSL 等级/回流焊峰值温度：Level-1-260C-UNLIM，引脚镀层/焊球材料：NIPDAU，TI官网SN74LVTH540DBR的批量USD价格：.649（1000+）

SN74LVTH540DW，工作温度：-40 to 85，封装：SOIC (DW)-20，包装数量MPQ：25个，MSL 等级/回流焊峰值温度：Level-1-260C-UNLIM，引脚镀层/焊球材料：NIPDAU，TI官网SN74LVTH540DW的批量USD价格：.708（1000+）

SN74LVTH540DWR，工作温度：-40 to 85，封装：SOIC (DW)-20，包装数量MPQ：2000个，MSL 等级/回流焊峰值温度：Level-1-260C-UNLIM，引脚镀层/焊球材料：NIPDAU，TI官网SN74LVTH540DWR的批量USD价格：.59（1000+）

SN74LVTH540PW，工作温度：-40 to 85，封装：TSSOP (PW)-20，包装数量MPQ：70个，MSL 等级/回流焊峰值温度：Level-1-260C-UNLIM，引脚镀层/焊球材料：NIPDAU，TI官网SN74LVTH540PW的批量USD价格：.708（1000+）

SN74LVTH540PWR，工作温度：-40 to 85，封装：TSSOP (PW)-20，包装数量MPQ：2000个，MSL 等级/回流焊峰值温度：Level-1-260C-UNLIM，引脚镀层/焊球材料：NIPDAU，TI官网SN74LVTH540PWR的批量USD价格：.59（1000+）

14-24-LOGIC-EVM — 支持 14 到 24 引脚 PW、DB、D、DW、NS、DYY 和 DGV 封装的通用逻辑 EVM

该 EVM 设计用于支持采用 14 至 24 引脚 D、DW、DB、NS、PW、DYY 或 DGV 封装的任何逻辑器件。