The TFP410 is a Texas Instruments PanelBus. flat panel display product, part of a comprehensive family of end-to-end digital visual interface (DVI) 1.0-compliant solutions, targeted at the PC and consumer electronics industry.

The TFP410 provides a universal interface to allow a glueless connection to most commonly available graphics controllers. Some of the advantages of this universal interface include selectable bus widths, adjustable signal levels, and differential and single-ended clocking. The adjustable 1.1-V to 1.8-V digital interface provides a low-EMI, high-speed bus that connects seamlessly with 12-bit or 24-bit interfaces. The DVI interface supports flat panel display resolutions up to UXGA at 165 MHz in 24-bit true color pixel format.

The TFP410 combines PanelBus circuit innovation with TI advanced 0.18-µm EPIC-5 CMOS process technology and ultralow ground inductance PowerPAD. package. The result is a compact 64-pin thin quad flat pack (TQFP) package providing a reliable, low-current, low-noise, high-speed digital interface solution.

• Controlled Baseline
  • One Assembly
  • One Test Site
  • One Fabrication Site
• Extended Temperature Performance of –55°C to 125°C
• Enhanced Diminishing Manufacturing Sources (DMS) Support
• Enhanced Product-Change Notification
• Qualification Pedigree(1)
• Digital Visual Interface (DVI) Compliant(2)
• Supports Pixel Rates Up to 165MHz (Including 1080p and WUXGA at 60Hz)
• Universal Graphics Controller Interface
  • 12-Bit Dual-Edge and 24-Bit Single-Edge Input Modes
  • Adjustable 1.1-V to 1.8-V and Standard 3.3-V CMOS Input Signal Levels
  • Fully Differential and Single-Ended Input Clocking Modes
  • Standard Intel? 12-Bit Digital Video Port Compatible as on Intel 81x Chipsets
• Enhanced PLL Noise Immunity
• On-Chip Regulators and Bypass Capacitors for Reducing System Costs
• Enhanced Jitter Performance
• No HSYNC Jitter Anomaly
• Negligible Data-Dependent Jitter
• Programmable Using I2C Serial Interface
• Monitor Detection Through Hot-Plug and Receiver Detection
• Single 3.3-V Supply Operation
• 64-Pin Thin Quad Flat Pack (TQFP) Using TI’s PowerPAD? Package
• TI Advanced 0.18-μm EPIC-5? CMOS Process Technology
• Pin Compatible With SiI164 DVI Transmitter

(1) Component qualification in accordance with JEDEC and industry standards to ensure reliable operation over an extended temperature range. This includes, but is not limited to, Highly Accelerated Stress Test (HAST) or biased 85/85, temperature cycle, autoclave or unbiased HAST, electromigration, bond intermetallic life, and mold compound life. Such qualification testing should not be viewed as justifying use of this component beyond specified performance and environmental limits. (2) The digital visual interface (DVI) specification is an industry standard developed by the digital display working group (DDWG) for high-speed digital connection to digital displays and has been adopted by industry-leading PC and consumer electronics manufacturers. The TFP410 is compliant to the DVI Revision 1.0 specification. PanelBus, PowerPAD, and EPIC-5 are trademarks of Texas Instruments. VESA is a trademark of Video Electronics Standards Association. Intel is a trademark of Intel Corporation.

• Protocols
• DVI, HDMI
• Speed (Max) (Gbps)
• 3.96
• Supply voltage (V)
• 3.3
• Operating temperature range (C)
• -55 to 125

TFP410-EP的完整型号有：TFP410MPAPREP、TFP410MPAPREPG4、V62/06653-01XE，以下是这些产品的关键参数及官网采购报价：

TFP410MPAPREP，工作温度：-55 to 125，封装：HTQFP (PAP)-64，包装数量MPQ：1000个，MSL 等级/回流焊峰值温度：Level-3-260C-168 HR，引脚镀层/焊球材料：NIPDAU，TI官网TFP410MPAPREP的批量USD价格：7.244（1000+）

TFP410MPAPREPG4，工作温度：-55 to 125，封装：HTQFP (PAP)-64，包装数量MPQ：1000个，MSL 等级/回流焊峰值温度：Level-3-260C-168 HR，引脚镀层/焊球材料：NIPDAU，TI官网TFP410MPAPREPG4的批量USD价格：7.244（1000+）

V62/06653-01XE，工作温度：-55 to 125，封装：HTQFP (PAP)-64，包装数量MPQ：1000个，MSL 等级/回流焊峰值温度：Level-3-260C-168 HR，引脚镀层/焊球材料：NIPDAU，TI官网V62/06653-01XE的批量USD价格：7.244（1000+）

PSPICE-FOR-TI — 适用于 TI 设计和模拟工具的 PSpice

PSpice for TI 可提供帮助评估模拟电路功能的设计和仿真环境。此功能齐全的设计和仿真套件使用 Cadence 的模拟分析引擎。PSpice for TI 可免费使用，包括业内超大的模型库之一，涵盖我们的模拟和电源产品系列以及精选的模拟行为模型。

借助?PSpice for TI 的设计和仿真环境及其内置的模型库，您可对复杂的混合信号设计进行仿真。创建完整的终端设备设计和原型解决方案，然后再进行布局和制造，可缩短产品上市时间并降低开发成本。

在?PSpice for TI 设计和仿真工具中，您可以搜索 TI (...)

TINA-TI — 基于 SPICE 的模拟仿真程序

TINA-TI 提供了 SPICE 所有的传统直流、瞬态和频域分析以及更多。TINA 具有广泛的后处理功能，允许您按照希望的方式设置结果的格式。虚拟仪器允许您选择输入波形、探针电路节点电压和波形。TINA 的原理图捕获非常直观 - 真正的“快速入门”。

TINA-TI 安装需要大约 500MB。直接安装，如果想卸载也很容易。我们相信您肯定会爱不释手。

TINA 是德州仪器 (TI) 专有的 DesignSoft 产品。该免费版本具有完整的功能，但不支持完整版 TINA 所提供的某些其他功能。

如需获取可用 TINA-TI 模型的完整列表，请参阅：SpiceRack - 完整列表

需要 HSpice (...)