The ’754C is a quad universal asynchronous receiver transmitter (UART) with 64-byte FIFOs, automatic hardware and software flow control, and data rates up to 3 Mbps. It incorporates the functionality of four UARTs, each UART having its own register set and FIFOs. The four UARTs share only the data bus interface and clock source, otherwise they operate independently. Another name for the UART function is Asynchronous Communications Element (ACE), and these terms are used interchangeably. The bulk of this document describes the behavior of each ACE, with the understanding that four such devices are incorporated into the ’754C. The ’754C offers enhanced features. It has a transmission control register (TCR) that stores received FIFO threshold level to start or stop transmission during hardware and software flow control. With the FIFO RDY register, the software gets the status of TXRDY/RXRDY for all four ports in one access. On-chip status registers provide the user with error indications, operational status, and modem interface control. System interrupts may be tailored to meet user requirements. An internal loopback capability allows onboard diagnostics.

Each UART transmits data sent to it from the peripheral 8-bit bus on the TX signal and receives characters on the RX signal. Characters can be programmed to be 5, 6, 7, or 8 bits. The UART has a 64-byte receive FIFO and transmit FIFO and can be programmed to interrupt at different trigger levels. The UART generates its own desired baud rate based upon a programmable divisor and its input clock. It can transmit even, odd, or no parity and 1-, 1.5-, or 2-stop bits. The receiver can detect break, idle or framing errors, FIFO overflow, and parity errors. The transmitter can detect FIFO underflow. The UART also contains a software interface for modem control operations, and software flow control and hardware flow control capabilities.

The ’754C is available in a 64-pin TQFP PM package. RXRDY and TXRDY functionality is not supported in the TL16C754CPM device.

• ST16C654/654D Pin Compatible With Additional Enhancements
• Support up to:
  • 24-MHz Crystal Input Clock (1.5Mbps)
  • 48-MHz Oscillator Input Clock (3Mbps) for 5-V Operation
  • 32-MHz Oscillator Input Clock (2Mbps) for 3.3-V Operation
  • 24-MHz Input Clock (1.5Mbps) for 2.5-V Operation
  • 16-MHz Input Clock (1Mbps) for 1.8-V Operation
• 64-Byte Transmit FIFO
• 64-Byte Receive FIFO With Error Flags
• Programmable and Selectable Transmit and Receive FIFO Trigger Levels for DMA and Interrupt Generation
• Programmable Receive FIFO Trigger Levels for Software/Hardware Flow Control
• Software/Hardware Flow Control
  • Programmable Xon/Xoff Characters
  • Programmable Auto-RTS and Auto-CTS
• Optional Data Flow Resume by Xon Any Character
• RS-485 Mode Support
• Support 1.8-V, 2.5-V, 3.3-V, or 5-V Supply
• Characterized for Operation From –40°C to 85°C, Available in Commercial and Industrial Temperature Grades
• Software-Selectable Baud-Rate Generator
• Prescaler Provides Additional Divide-by-4 Function
• Programmable Sleep Mode
• Programmable Serial Interface Characteristics
  • 5-, 6-, 7-, or 8-Bit Characters
  • Even, Odd, or No Parity Bit Generation and Detection
  • 1-, 1.5-, or 2-Stop Bit Generation
• False Start Bit Detection
• Complete Status Reporting Capabilities in Both Normal and Sleep Mode
• Line Break Generation and Detection
• Internal Test and Loopback Capabilities
• Fully Prioritized Interrupt System Controls
• Modem Control Functions (CTS, RTS, DSR, DTR, RI, and CD)
• Infrared Data Association (IrDA) Capability

• Number of channels (#)
• 4
• FIFOs (bytes)
• 64
• Rx FIFO trigger levels (#)
• 16
• Tx FIFO trigger levels (#)
• 16
• Programmable FIFO trigger levels
• Yes
• CPU interface
• X86
• Baud rate (max) at Vcc = 1.8 V & with 16X sampling (Mbps)
• 1
• Baud rate (max) at Vcc = 2.5 V & with 16X sampling (Mbps)
• 1.5
• Baud rate (max) at Vcc = 3.3 V & with 16X sampling (Mbps)
• 2
• Baud rate (max) at Vcc = 5.0 V & with 16X sampling (Mbps)
• 3
• Operating voltage (V)
• 1.8, 2.5, 3.3, 5
• Auto RTS/CTS
• Yes
• Rating
• Catalog
• Operating temperature range (C)
• 0 to 70, -40 to 85

TL16C754C的完整型号有：TL16CP754CIPM、TL16CP754CIPMR、TL16CP754CPM、TL16CP754CPMR，以下是这些产品的关键参数及官网采购报价：

TL16CP754CIPM，工作温度：-40 to 85，封装：LQFP (PM)-64，包装数量MPQ：160个，MSL 等级/回流焊峰值温度：Level-3-260C-168 HR，引脚镀层/焊球材料：NIPDAU，TI官网TL16CP754CIPM的批量USD价格：8.179（1000+）

TL16CP754CIPMR，工作温度：-40 to 85，封装：LQFP (PM)-64，包装数量MPQ：1000个，MSL 等级/回流焊峰值温度：Level-3-260C-168 HR，引脚镀层/焊球材料：NIPDAU，TI官网TL16CP754CIPMR的批量USD价格：6.959（1000+）

TL16CP754CPM，工作温度：0 to 70，封装：LQFP (PM)-64，包装数量MPQ：160个，MSL 等级/回流焊峰值温度：Level-3-260C-168 HR，引脚镀层/焊球材料：NIPDAU，TI官网TL16CP754CPM的批量USD价格：7.935（1000+）

TL16CP754CPMR，工作温度：0 to 70，封装：LQFP (PM)-64，包装数量MPQ：1000个，MSL 等级/回流焊峰值温度：Level-3-260C-168 HR，引脚镀层/焊球材料：NIPDAU，TI官网TL16CP754CPMR的批量USD价格：6.714（1000+）

TL16C754C 5V PM Package IBIS Model

PSpice for TI 可提供帮助评估模拟电路功能的设计和仿真环境。此功能齐全的设计和仿真套件使用 Cadence 的模拟分析引擎。PSpice for TI 可免费使用，包括业内超大的模型库之一，涵盖我们的模拟和电源产品系列以及精选的模拟行为模型。

借助?PSpice for TI 的设计和仿真环境及其内置的模型库，您可对复杂的混合信号设计进行仿真。创建完整的终端设备设计和原型解决方案，然后再进行布局和制造，可缩短产品上市时间并降低开发成本。

在?PSpice for TI 设计和仿真工具中，您可以搜索 TI (...)

TINA-TI — 基于 SPICE 的模拟仿真程序

TINA-TI 提供了 SPICE 所有的传统直流、瞬态和频域分析以及更多。TINA 具有广泛的后处理功能，允许您按照希望的方式设置结果的格式。虚拟仪器允许您选择输入波形、探针电路节点电压和波形。TINA 的原理图捕获非常直观 - 真正的“快速入门”。

TINA-TI 安装需要大约 500MB。直接安装，如果想卸载也很容易。我们相信您肯定会爱不释手。

TINA 是德州仪器 (TI) 专有的 DesignSoft 产品。该免费版本具有完整的功能，但不支持完整版 TINA 所提供的某些其他功能。

如需获取可用 TINA-TI 模型的完整列表，请参阅：SpiceRack - 完整列表

需要 HSpice (...)