The TL28L92 is a pin and function replacement for the SC26C92 operating at 3.3 V or 5 V supply with added features and deeper FIFOs. Its configuration on power-up is that of the SC26C92. Its differences from the SC26C92 are: 16 character receiver, 16 character transmit FIFOs, watchdog timer for each receiver, mode register 0 is added, extended baud rate and overall faster speeds, programmable receiver and transmitter interrupts.

Pin programming will allow the device to operate with either the Motorola or Intel bus interface. The bit 3 of the MR0A register allows the device to operate in an 8 byte FIFO mode if strict compliance with the SC26C92 FIFO structure is required.

The Texas Instruments TL28L92 Dual Universal Asynchronous Receiver/Transmitter (DUART) is a single-chip CMOS-LSI communications device that provides two full-duplex asynchronous receiver/transmitter channels in a single package. It interfaces directly with microprocessors and may be used in a polled or interrupt driven system with modem and DMA interface.

The operating mode and data format of each channel can be programmed independently. Additionally, each receiver and transmitter can select its operating speed as one of 28 fixed baud rates; a 16× clock derived from a programmable counter/timer, or an external 1× or 16× clock. The baud rate generator and counter/timer can operate directly from a crystal or from external clock inputs. The ability to independently program the operating speed of the receiver and transmitter make the DUART particularly attractive for dual-speed channel applications such as clustered terminal systems.

Each receiver and transmitter is buffered by 8 or 16 character FIFOs to minimize the potential of receiver overrun, transmitter underrun and to reduce interrupt overhead in interrupt driven systems. In addition, a flow control capability is provided via RTS/CTS signaling to disable a remote transmitter when the receiver buffer is full. Also provided on the TL28L92 are a multipurpose 7-bit input port and a multipurpose 8-bit output port. These can be used as general purpose I/O ports or can be assigned specific functions (such as clock inputs or status/interrupt outputs) under program control.

The TL28L92 is available now in 44-pin QFP (FR), and will be available 2Q09 in 48-pin QFN (RGZ).

• SC28L92 Pin Compatible
• 3.3 V to 5.0 V, –40°C to 85°C and 68xxx or 80xxx Bus Interface
• Dual Full-Duplex Independent Asynchronous Receiver/Transmitters 16 Character FIFOs for Each Receiver and Transmitter
• Pin Programming Selects 68xxx or 80xxx Bus Interface
• Programmable Data Format
  • 5 Data to 8 Data Bits Plus Parity
  • Odd, Even, No Parity or Force Parity
  • 1 Stop, 1.5 Stop or 2 Stop Bits Programmable in 1/16-Bit Increments
• 16-Bit Programmable Counter/Timer
• Programmable Baud Rate for Each Receiver and Transmitter Selectable From:
  • 28 Fixed Rates: 50 Bd to 230.4 kBd
  • Other Baud Rates to 1 MHz at 16×
  • Programmable User-Defined Rates Derived From a Programmable Counter/Timer
• External 1× or 16× Clock
• Parity, Framing, and Overrun Error Detection
• False Start Bit Detection
• Line Break Detection and Generation
• Programmable Channel Mode
  • Normal (Full-Duplex)
  • Automatic Echo
  • Local Loopback
  • Remote Loopback
  • Multi-Drop Mode (Also Called Wake-Up or 9-Bit)
• Multi-Function 7-Bit Input Port (Includes IACKN)
  • Can Serve as Clock or Control Inputs
  • Change of State Detection on Four Inputs Inputs Have Typically > 100 k Pullup Resistors
  • Change of State Detectors for Modem Control
• Multi-Function 8-Bit Output Port
  • Individual Bit Set/Reset Capability
  • Outputs Can Be Programmed to Be Status/Interrupt Signals
  • FIFO Status for DMA Interface
• Versatile Interrupt System
  • Single Interrupt Output With Eight Maskable Interrupting Conditions
  • Output Port Can be Configured to Provide a Total of up to Five Separate Interrupt Outputs That May be Wire ORed
  • Each FIFO Can be Programmed for Four Different Interrupt Levels
  • Watchdog Timer for Each Receiver
• Maximum Data Transfer Rates: 1× – 1 Mbit/s, 16× – 1 Mbit/s
• Automatic Wake-Up Mode for Multi-Drop Applications
• Start-End Break Interrupt/Status
• Detects Break Which Originates in the Middle of a Character
• On-Chip Crystal Oscillator
• Powerdown Mode
• Receiver Time-Out Mode
• Single 3.3 V or 5 V Power Supply
• Powers up to Emulate SC26C92
• Meets or Exceeds JEDEC 14C ESD Requirements

• Number of channels (#)
• 2
• FIFOs (bytes)
• 16
• Rx FIFO trigger levels (#)
• 4
• Tx FIFO trigger levels (#)
• 4
• Programmable FIFO trigger levels
• Yes
• CPU interface
• X86 or 68K
• Baud rate (max) at Vcc = 1.8 V & with 16X sampling (Mbps)
• —
• Baud rate (max) at Vcc = 2.5 V & with 16X sampling (Mbps)
• —
• Baud rate (max) at Vcc = 3.3 V & with 16X sampling (Mbps)
• 1
• Baud rate (max) at Vcc = 5.0 V & with 16X sampling (Mbps)
• 1
• Operating voltage (V)
• 3.3, 5
• Auto RTS/CTS
• Yes
• Rating
• Catalog
• Operating temperature range (C)
• -40 to 85, 0 to 70

TL28L92的完整型号有：TL28L92FR、TL28L92IFR，以下是这些产品的关键参数及官网采购报价：

TL28L92FR，工作温度：0 to 70，封装：QFP (FR)-44，包装数量MPQ：96个，MSL 等级/回流焊峰值温度：Level-3-220C-168HRS，引脚镀层/焊球材料：SN，TI官网TL28L92FR的批量USD价格：6.098（1000+）

TL28L92IFR，工作温度：-40 to 85，封装：QFP (FR)-44，包装数量MPQ：96个，MSL 等级/回流焊峰值温度：Level-3-260C-168 HR，引脚镀层/焊球材料：SN，TI官网TL28L92IFR的批量USD价格：6.32（1000+）

PSPICE-FOR-TI — 适用于 TI 设计和模拟工具的 PSpice

PSpice for TI 可提供帮助评估模拟电路功能的设计和仿真环境。此功能齐全的设计和仿真套件使用 Cadence 的模拟分析引擎。PSpice for TI 可免费使用，包括业内超大的模型库之一，涵盖我们的模拟和电源产品系列以及精选的模拟行为模型。

借助?PSpice for TI 的设计和仿真环境及其内置的模型库，您可对复杂的混合信号设计进行仿真。创建完整的终端设备设计和原型解决方案，然后再进行布局和制造，可缩短产品上市时间并降低开发成本。

在?PSpice for TI 设计和仿真工具中，您可以搜索 TI (...)

TINA-TI — 基于 SPICE 的模拟仿真程序

TINA-TI 提供了 SPICE 所有的传统直流、瞬态和频域分析以及更多。TINA 具有广泛的后处理功能，允许您按照希望的方式设置结果的格式。虚拟仪器允许您选择输入波形、探针电路节点电压和波形。TINA 的原理图捕获非常直观 - 真正的“快速入门”。

TINA-TI 安装需要大约 500MB。直接安装，如果想卸载也很容易。我们相信您肯定会爱不释手。

TINA 是德州仪器 (TI) 专有的 DesignSoft 产品。该免费版本具有完整的功能，但不支持完整版 TINA 所提供的某些其他功能。

如需获取可用 TINA-TI 模型的完整列表，请参阅：SpiceRack - 完整列表

需要 HSpice (...)