The TLC59116 is an I²C bus controlled 16-channel LED driver that is optimized for red/green/blue/amber (RGBA) color mixing and backlight application. Each LED output has its own 8-bit resolution (256 steps) fixed-frequency individual PWM controller that operates at 97 kHz, with a duty cycle that is adjustable from 0% to 99.6%.

The individual PWM controller allows each LED to be set to a specific brightness value. An additional 8-bit resolution (256 steps) group PWM controller has both a fixed frequency of 190 Hz and an adjustable frequency between 24 Hz to once every 10.73 seconds, with a duty cycle that is adjustable from 0% to 99.6%. The group PWM controller dims or blinks all LEDs with the same value.

Each LED output can be off, on (no PWM control), or set at its individual PWM controller value at both individual and group PWM controller values.

The TLC59116 operates with a supply voltage range of 3 V to 5.5 V and the outputs are 17 V tolerant. LEDs can be directly connected to the TLC59116 device outputs.

Software programmable LED Group and three Sub Call I²C-bus addresses allow all or defined groups of TLC59116 devices to respond to a common I²C-bus address, allowing for example, all the same color LEDs to be turned on or off at the same time or marquee chasing effect, thus minimizing I²C-bus commands.

Four hardware address pins allow up to 14 devices on the same bus.

The Software Reset (SWRST) Call allows the master to perform a reset of the TLC59116 through the I²C-bus, identical to the Power-On Reset (POR) that initializes the registers to their default state causing the outputs to be set high (LED off). This allows an easy and quick way to reconfigure all device registers to the same condition.

• 16 LED Drivers (Each Output Programmable at Off, On, Programmable LED Brightness, or Programmable Group Dimming and Blinking Mixed With Individual LED Brightness)
• 16 Constant-Current Output Channels
• 256-Step (8-Bit) Linear Programmable Brightness Per LED Output Varying From Fully Off (Default) to Maximum Brightness Using a 97-kHz PWM Signal
• 256-Step Group Brightness Control Allows General Dimming [Using a 190-Hz PWM Signal From Fully Off to Maximum Brightness (Default)]
• 256-Step Group Blinking With Frequency Programmable From 24Hz to 10.73s and Duty Cycle From 0% to 99.6%
• Four Hardware Address Pins Allow 14 TLC59116 Devices to Be Connected to Same I2C Bus
• Four Software-Programmable I2C Bus Addresses (One LED Group Call Address and Three LED Sub Call Addresses) Allow Groups of Devices to Be Addressed at Same Time in Any Combination
• Software Reset Feature (SWRST Call) Allows Device to Be Reset Through I2C Bus
• Up to 14 Possible Hardware-Adjustable Individual I2C Bus Addresses Per Device, So That Each Device Can Be Programmed
• Open-Load and Overtemperature Detection Mode to Detect Individual LED Errors
• Output State Change Programmable on Acknowledge or Stop Command to Update Outputs Byte-by-Byte or All at Same Time (Default toChange on Stop)
• Output Current Adjusted Through an External Resistor
• Constant Output Current Range: 5mA to 120mA
• Maximum Output Voltage: 17V
• 25-MHz Internal Oscillator Requires No External Components
• 1-MHz Fast-mode Plus (FMT) Compatible I2C Bus Interface With 30-mA High-Drive Capability on SDA Output for Driving High-Capacitive Buses
• Internal Power-On Reset
• Noise Filter on SCL and SDA Inputs
• No Glitch on Power-Up
• Active-Low Reset
• Supports Hot Insertion
• Low Standby Current
• 3.3-V or 5-V Supply Voltage
• 5.5-V Tolerant Inputs
• Offered in 28-Pin Thin Shrink Small-Outline Package (TSSOP) (PW) and 32-Pin Quad Flatpack No Lead (QFN)
• –40 °C to 85 °C Operation
• APPLICATIONS
  • Gaming
  • Small Signage
  • Industrial Equipment

All other trademarks are the property of their respective owners

• Number of channels (#)
• 16
• LED current per channel (mA)
• 120
• LED configuration
• Parallel, Series, Single
• Vin (Min) (V)
• 3
• Vin (Max) (V)
• 5.5
• Iout (Max) (A)
• 1.92
• Features
• Analog/PWM mixed dimming, Constant current, Current control, I2C control
• Iq (Typ) (mA)
• 25
• Operating temperature range (C)
• -40 to 85
• Rating
• Catalog

TLC59116的完整型号有：TLC59116IPWR、TLC59116IRHBR，以下是这些产品的关键参数及官网采购报价：

TLC59116IPWR，工作温度：-40 to 85，封装：TSSOP (PW)-28，包装数量MPQ：2000个，MSL 等级/回流焊峰值温度：Level-1-260C-UNLIM，引脚镀层/焊球材料：NIPDAU，TI官网TLC59116IPWR的批量USD价格：.968（1000+）

TLC59116IRHBR，工作温度：-40 to 85，封装：VQFN (RHB)-32，包装数量MPQ：3000个，MSL 等级/回流焊峰值温度：Level-2-260C-1 YEAR，引脚镀层/焊球材料：NIPDAU，TI官网TLC59116IRHBR的批量USD价格：.968（1000+）

TLC59116EVM-390 — 16 通道 LED 驱动器评估模块

TLC59116 是 I2C 总线控制的 16 通道 LED 驱动器，它针对娱乐产品的红色/绿色/蓝色/琥珀色 (RGBA) 混合和背光应用进行了优化。每个 LED 输出都拥有自身的 8 位分辨率（256 色阶）、固定频率、独立 PWM 控制器（工作频率为 97kHz）和可调节占空比（0% 至 99.6%）。独立 PWM 控制器允许将每个 LED 设置为特定的亮度值。附加的 8 位分辨率（256 色阶）组合式 PWM 控制器既具有 190Hz 的固定频率，又拥有低至 24Hz 的可调节频率（每隔 10.73 秒调节一次）和可调节占空比（0% 至 99.6%）。组合式 PWM (...)

TLC591XXSW-LINUX — 用于 TLC591XX 的 Linux 驱动程序

The Linux driver supports the TLC591XX series of Constant-Current LED Sink Drivers. The Linux driver supports communication through the I2C bus and interfaces with the LED sub-system.

Linux Mainline Status

Available in Linux Main line: Yes
Available through git.ti.com: N/A

Supported Devices:

• tlc59116
• (...)

PSPICE-FOR-TI — 适用于 TI 设计和模拟工具的 PSpice

PSpice for TI 可提供帮助评估模拟电路功能的设计和仿真环境。此功能齐全的设计和仿真套件使用 Cadence 的模拟分析引擎。PSpice for TI 可免费使用，包括业内超大的模型库之一，涵盖我们的模拟和电源产品系列以及精选的模拟行为模型。

借助?PSpice for TI 的设计和仿真环境及其内置的模型库，您可对复杂的混合信号设计进行仿真。创建完整的终端设备设计和原型解决方案，然后再进行布局和制造，可缩短产品上市时间并降低开发成本。

在?PSpice for TI 设计和仿真工具中，您可以搜索 TI (...)

TIDA-03026 — 使用 LED 和音频反馈的状态指示参考设计

TIDA-03026 参考设计功能仿真了各种终端设备中的状态指示子系统。通过将多个 LED 驱动器并联，可使 RGB LED 阵列同步呈现闪烁、脉冲、呼吸灯光效果 - 增强客户体验。同时还集成了音频反馈，以通过 LED 和音频显示一种合并的状态指示解决方案。应用包括 IP 电话、楼宇自动化、家庭自动化、白色家电以及汽车信息娱乐系统和集群。