The TLC59116F is an I²C-bus controlled 16-channel LED driver optimized for red/green/blue/amber (RGBA) color mixing applications. Each LED output has its own 8-bit resolution (256 steps) fixed frequency individual PWM controller that operates at 97 kHz with a duty cycle that is adjustable from 0% to 99.6% to allow the LED to be set to a specific brightness value. An additional 8-bit resolution (256 steps) group PWM controller has both a fixed frequency of 190 Hz and an adjustable frequency between 24 Hz to once every 10.73 seconds with a duty cycle that is adjustable from 0% to 99.6% that is used to either dim or blink all LEDs with the same value.

• 16 LED Drivers (Each Output Programmable at OFF, ON, LED Brightness, and Group Dimming/Blinking Mixed With Individual LED Brightness)
• 16 Open-Drain Output Channels
• 256-Step (8-Bit) Linear Programmable Brightness Per LED Output Varying From Fully OFF (Default) to Maximum Brightness Using a 97-kHz PWM Signal
• 256-Step Group Brightness Control Allows General Dimming (Using a 190-Hz PWM Signal From Fully OFF to Maximum Brightness (Default)
• 256-Step Group Blinking With Frequency Programmable From 24 Hz to 10.73 s and Duty Cycle from 0% to 99.6%
• Four Hardware Address Pins Allow 14 TLC59116F Devices to be Connected to the Same I2C Bus
• Four Software-Programmable I2C Bus Addresses (One LED Group Call Address and Three LED Sub-Call Addresses) Allow Groups of Devices to be AddressedSimultaneously in Any Combination (For example, One Register Used for ‘All Call’ So All the TLC59116Fs on the I2C Bus Can be Addressed at the Same Time and the Second Register Used for Three Different Addresses So That 1/3 of all Devices on the Bus Can Be Addressed at the Same Time in a Group). Software Enable and Disable for I2C Bus Address.
• Software Reset Feature (SWRST Call) Allows the Device to be Reset Through the I2C Bus
• Up to 14 Possible Hardware Adjustable Individual I2C Bus Addresses Per Device so That Each Device Can be Programmed
• Output State Change Programmable on the Acknowledge or the STOP Command to Update Outputs Byte-by-Byte or All at the Same Time (Default to Change on STOP.
• 120-mA Maximum Output Current
• 17-V Maximum Output Voltage
• 25-MHz Internal Oscillator Requires No External Components
• 1-MHz Fast-Mode Plus (FM+) Compatible I2C Bus Interface With 30 mA High Drive Capability on SDA Output for Driving High Capacity Buses
• Internal Power-On Reset
• Noise Filter on SCL/SDA Inputs
• No Glitch on Power Up
• Active-Low Reset
• Supports Hot Insertion
• Low Standby Current
• 3.3-V or 5-V Supply Voltage
• 5.5-V Tolerant Inputs
• 28-Pin TSSOP (PW)
• –40°C to 85°C Operation
• APPLICATIONS
  • Gaming
  • Small Signage
  • Industrial Equipment

All other trademarks are the property of their respective owners

• Number of channels (#)
• 16
• LED current per channel (mA)
• 120
• LED configuration
• Parallel, Series, Single
• Program memory
• No
• Programmable ramp control
• No
• Vin (Min) (V)
• 3
• Vin (Max) (V)
• 5.5
• Iout (Max) (A)
• 1.92
• Features
• I2C control
• Iq (Typ) (mA)
• 13
• Operating temperature range (C)
• -40 to 85
• Rating
• Catalog

TLC59116F的完整型号有：TLC59116FIPWR、TLC59116FIRHBR，以下是这些产品的关键参数及官网采购报价：

TLC59116FIPWR，工作温度：-40 to 85，封装：TSSOP (PW)-28，包装数量MPQ：2000个，MSL 等级/回流焊峰值温度：Level-1-260C-UNLIM，引脚镀层/焊球材料：NIPDAU，TI官网TLC59116FIPWR的批量USD价格：.968（1000+）

TLC59116FIRHBR，工作温度：-40 to 85，封装：VQFN (RHB)-32，包装数量MPQ：3000个，MSL 等级/回流焊峰值温度：Level-2-260C-1 YEAR，引脚镀层/焊球材料：NIPDAU，TI官网TLC59116FIRHBR的批量USD价格：.968（1000+）

TLC59116FEVM-571 — 16 通道 LED 驱动器评估模块

TLC59116F 是 I2C 总线控制的 16 通道 LED 驱动器，它针对娱乐产品的红色/绿色/蓝色/琥珀色 (RGBA) 混合和背光应用进行了优化。每个 LED 输出都拥有自身的 8 位分辨率（256 色阶）、固定频率、独立 PWM 控制器（工作频率为 97kHz）和可调节占空比（0% 至 99.6%）。独立 PWM 控制器允许将每个 LED 设置为特定的亮度值。附加的 8 位分辨率（256 色阶）组合式 PWM 控制器既具有 190Hz 的固定频率，又拥有低至 24Hz 的可调节频率（每隔 10.73 秒调节一次）和可调节占空比（0% 至 99.6%）。组合式 PWM (...)

PSPICE-FOR-TI — 适用于 TI 设计和模拟工具的 PSpice

PSpice for TI 可提供帮助评估模拟电路功能的设计和仿真环境。此功能齐全的设计和仿真套件使用 Cadence 的模拟分析引擎。PSpice for TI 可免费使用，包括业内超大的模型库之一，涵盖我们的模拟和电源产品系列以及精选的模拟行为模型。

借助?PSpice for TI 的设计和仿真环境及其内置的模型库，您可对复杂的混合信号设计进行仿真。创建完整的终端设备设计和原型解决方案，然后再进行布局和制造，可缩短产品上市时间并降低开发成本。

在?PSpice for TI 设计和仿真工具中，您可以搜索 TI (...)