The TMS320C6745/6747 device is a low-power digital signal processor based on a TMS320C674x DSP core. It consumes significantly lower power than other members of the TMS320C6000™ platform of DSPs.

The TMS320C6745/6747 device enables original-equipment manufacturers (OEMs) and original-design manufacturers (ODMs) to quickly bring to market devices featuring high processing performance .

The TMS320C6745/6747 DSP core uses a two-level cache-based architecture. The Level 1 program cache (L1P) is a 32-KB direct mapped cache and the Level 1 data cache (L1D) is a 32-KB 2-way set-associative cache. The Level 2 program cache (L2P) consists of a 256-KB memory space that is shared between program and data space. L2 memory can be configured as mapped memory, cache, or combinations of the two. Although the DSP L2 is accessible by other hosts in the system, an additional 128KB of RAM shared memory (TMS320C6747 only) is available for use by other hosts without affecting DSP performance.

The peripheral set includes: a 10/100 Mbps Ethernet MAC (EMAC) with a management data input/output (MDIO) module; two I²C Bus interfaces; 3 multichannel audio serial ports (McASPs) with 16/9 serializers and FIFO buffers; two 64-bit general-purpose timers each configurable (one configurable as watchdog); a configurable 16-bit host-port interface (HPI) [TMS320C6747 only]; up to 8 banks of 16 pins of general-purpose input/output (GPIO) with programmable interrupt/event generation modes, multiplexed with other peripherals; 3 UART interfaces (one with both RTS and CTS); three enhanced high-resolution pulse width modulator (eHRPWM) peripherals; three 32-bit enhanced capture (eCAP) module peripherals which can be configured as 3 capture inputs or 3 auxiliary pulse width modulator (APWM) outputs; two 32-bit enhanced quadrature encoded pulse (eQEP) peripherals; and 2 external memory interfaces: an asynchronous and SDRAM external memory interface (EMIFA) for slower memories or peripherals, and a higher speed memory interface (EMIFB) for SDRAM.

The Ethernet Media Access Controller (EMAC) provides an efficient interface between the TMS320C6745/6747 device and the network. The EMAC supports both 10Base-T and 100Base-TX, or 10 Mbps and 100 Mbps in either half- or full-duplex mode. Additionally, an MDIO interface is available for PHY configuration.

The rich peripheral set provides the ability to control external peripheral devices and communicate with external processors. For details on each of the peripherals, see the related sections later in this document and the associated peripheral reference guides.

• Software Support
  • TI DSP/BIOS?
  • Chip Support Library and DSP Library
• 375- and 456-MHz TMS320C674x VLIW DSP
• C674x Instruction Set Features
  • Superset of the C67x+ and C64x+ ISAs
  • Up to 3648 MIPS and 2736 MFLOPS C674x
  • Byte-Addressable (8-, 16-, 32-, and 64-Bit Data)
  • 8-Bit Overflow Protection
  • Bit-Field Extract, Set, Clear
  • Normalization, Saturation, Bit-Counting
  • Compact 16-Bit Instructions
• C674x Two-Level Cache Memory Architecture
  • 32KB of L1P Program RAM/Cache
  • 32KB of L1D Data RAM/Cache
  • 256KB of L2 Unified Mapped RAM/Cache
  • Flexible RAM/Cache Partition (L1 and L2)
• Enhanced Direct Memory Access Controller 3 (EDMA3):
  • 2 Transfer Controllers
  • 32 Independent DMA Channels
  • 8 Quick DMA Channels
  • Programmable Transfer Burst Size
• TMS320C674x Fixed- and Floating-Point VLIW DSP Core
  • Load-Store Architecture with Nonaligned Support
  • 64 General-Purpose Registers (32-Bit)
  • Six ALU (32- and 40-Bit) Functional Units
    • Supports 32-Bit Integer, SP (IEEE Single Precision/32-Bit) and DP (IEEE Double Precision/64-Bit) Floating Point
    • Supports up to Four SP Additions Per Clock, Four DP Additions Every 2 Clocks
    • Supports up to Two Floating-Point (SP or DP) Reciprocal Approximation (RCPxP) and Square-Root Reciprocal Approximation (RSQRxP) Operations Per Cycle
  • Two Multiply Functional Units
    • Mixed-Precision IEEE Floating Point Multiply Supported up to:
      • 2 SP x SP -> SP Per Clock
      • 2 SP x SP -> DP Every Two Clocks
      • 2 SP x DP -> DP Every Three Clocks
      • 2 DP x DP -> DP Every Four Clocks
    • Fixed-Point Multiply Supports Two 32 x 32-Bit Multiplies, Four 16 x 16-Bit Multiplies, or Eight 8 x 8-Bit Multiplies per Clock Cycle, and Complex Multiples
  • Instruction Packing Reduces Code Size
  • All Instructions Conditional
  • Hardware Support for Modulo Loop Operation
  • Protected Mode Operation
  • Exceptions Support for Error Detection and Program Redirection
• 128KB of RAM Shared Memory (TMS320C6747 Only)
• 3.3-V LVCMOS I/Os (Except for USB Interfaces)
• Two External Memory Interfaces:
  • EMIFA
    • NOR (8- or 16-Bit-Wide Data)
    • NAND (8- or 16-Bit-Wide Data)
    • 16-Bit SDRAM with 128-MB Address Space (TMS320C6747 Only)
  • EMIFB
    • 32-Bit or 16-Bit SDRAM with 256-MB Address Space (TMS320C6747)
    • 16-Bit SDRAM with 128-MB Address Space (TMS320C6745)
• Three Configurable 16550-Type UART Modules:
  • UART0 with Modem Control Signals
  • Autoflow Control Signals (CTS, RTS) on UART0 Only
  • 16-Byte FIFO
  • 16x or 13x Oversampling Option
• LCD Controller (TMS320C6747 Only)
• Two Serial Peripheral Interfaces (SPIs) Each with One Chip Select
• Multimedia Card (MMC)/Secure Digital (SD) Card Interface with Secure Data I/O (SDIO)
• Two Master and Slave Inter-Integrated Circuit (I2C Bus?)
• One Host-Port Interface (HPI) with 16-Bit-Wide Muxed Address/Data Bus for High Bandwidth (TMS320C6747 Only)
• Programmable Real-Time Unit Subsystem (PRUSS)
  • Two Independent Programmable Realtime Unit (PRU) Cores
    • 32-Bit Load and Store RISC Architecture
    • 4KB of Instruction RAM per Core
    • 512 Bytes of Data RAM per Core
    • PRUSS can be Disabled via Software to Save Power
  • Standard Power-Management Mechanism
    • Clock Gating
    • Entire Subsystem Under a Single PSC Clock Gating Domain
  • Dedicated Interrupt Controller
  • Dedicated Switched Central Resource
• USB 1.1 OHCI (Host) with Integrated PHY (USB1) (TMS320C6747 Only)
• USB 2.0 OTG Port with Integrated PHY (USB0)
  • USB 2.0 High- and Full-Speed Client (TMS320C6747)
  • USB 2.0 Full-Speed Client (TMS320C6745)
  • USB 2.0 High-, Full-, and Low-Speed Host (TMS320C6747)
  • USB 2.0 Full- and Low-Speed Host (TMS320C6745)
  • High-Speed Functionality Available on TMS320C6747 Device Only
  • End Point 0 (Control)
  • End Points 1,2,3,4 (Control, Bulk, Interrupt or ISOC) RX and TX
• Three Multichannel Audio Serial Ports (McASPs):
  • TMS320C6747 Supports 3 McASPs
  • TMS320C6745 Supports 2 McASPs
  • Six Clock Zones and 28 Serial Data Pins
  • Supports TDM, I2S, and Similar Formats
  • DIT-Capable (McASP2)
  • FIFO Buffers for Transmit and Receive
• 10/100 Mbps Ethernet MAC (EMAC):
  • IEEE 802.3 Compliant (3.3-V I/O Only)
  • RMII Media-Independent Interface
  • Management Data I/O (MDIO) Module
• Real-Time Clock with 32-kHz Oscillator and Separate Power Rail (TMS320C6747 Only)
• One 64-Bit General-Purpose Timer (Configurable as Two 32-Bit Timers)
• One 64-Bit General-Purpose Watchdog Timer (Configurable as Two 32-Bit General-Purpose Timers)
• Three Enhanced Pulse Width Modulators (eHRPWMs):
  • Dedicated 16-Bit Time-Base Counter with Period and Frequency Control
  • 6 Single Edge, 6 Dual Edge Symmetric, or 3 Dual Edge Asymmetric Outputs
  • Dead-Band Generation
  • PWM Chopping by High-Frequency Carrier
  • Trip Zone Input
• Three 32-Bit Enhanced Capture (eCAP) Modules:
  • Configurable as 3 Capture Inputs or 3 Auxiliary Pulse Width Modulator (APWM) Outputs
  • Single-Shot Capture of up to Four Event Time-Stamps
• Two 32-Bit Enhanced Quadrature Encoder Pulse (eQEP) Modules
• TMS320C6747 Device:
  • 256-Ball Pb-Free Plastic Ball Grid Array (PBGA) [ZKB Suffix], 1.0-mm Ball Pitch
• TMS320C6745 Device:
  • 176-pin PowerPAD? Plastic Quad Flat Pack [PTP suffix], 0.5-mm Pin Pitch
• Commercial, Industrial, Extended, or Automotive Temperature

• DSP
• 1 C674x
• DSP MHz (Max)
• 375, 456
• CPU
• 32-/64-bit
• Operating system
• TI-RTOS
• Ethernet MAC
• 10/100
• Rating
• Catalog
• Operating temperature range (C)
• -40 to 105, -40 to 125, -40 to 90, 0 to 90

TMS320C6745的完整型号有：TMS320C6745DPTP3、TMS320C6745DPTP4、TMS320C6745DPTPA3、TMS320C6745DPTPD4、TMS320C6745DPTPT3，以下是这些产品的关键参数及官网采购报价：

TMS320C6745DPTP3，工作温度：0 to 90，封装：HLQFP (PTP)-176，包装数量MPQ：40个，MSL 等级/回流焊峰值温度：Level-4-260C-72 HR，引脚镀层/焊球材料：Call TI，TI官网TMS320C6745DPTP3的批量USD价格：7.779（1000+）

TMS320C6745DPTP4，工作温度：PropertyValue，封装：HLQFP (PTP)-176，包装数量MPQ：40个，MSL 等级/回流焊峰值温度：Level-4-260C-72 HR，引脚镀层/焊球材料：Call TI，TI官网TMS320C6745DPTP4的批量USD价格：9.335（1000+）

TMS320C6745DPTPA3，工作温度：-40 to 105，封装：HLQFP (PTP)-176，包装数量MPQ：40个，MSL 等级/回流焊峰值温度：Level-4-260C-72 HR，引脚镀层/焊球材料：Call TI，TI官网TMS320C6745DPTPA3的批量USD价格：9.335（1000+）

TMS320C6745DPTPD4，工作温度：-40 to 90，封装：HLQFP (PTP)-176，包装数量MPQ：40个，MSL 等级/回流焊峰值温度：Level-4-260C-72 HR，引脚镀层/焊球材料：NIPDAU，TI官网TMS320C6745DPTPD4的批量USD价格：10.502（1000+）

TMS320C6745DPTPT3，工作温度：-40 to 125，封装：HLQFP (PTP)-176，包装数量MPQ：40个，MSL 等级/回流焊峰值温度：Level-4-260C-72 HR，引脚镀层/焊球材料：NIPDAU，TI官网TMS320C6745DPTPT3的批量USD价格：9.335（1000+）

TMDSOSKL137 — OMAP-L137/TMS320C6747 浮点入门套件

与 Spectrum Digital Inc. 联合开发的 OMAP-L137/TMS320C6747 浮点入门套件是低成本开发平台，旨在加快基于 TI OMAP-L13x 应用处理器和 TMS320C674x 定点/浮点 DSP（TMS320C6747、TMS320C6745 和 TMS320C6743）的高精度应用的开发速度。该套件使用 USB 通信来真正实现即插即用功能。初级和熟练的设计人员都可以使用该入门套件的全功能 Code Composer StudioTM 集成开发环境 (IDE) 和 eXpressDSPTM 软件（包含 DSP/BIOS (...)

TMDSEMU200-U — Spectrum Digital XDS200 USB 仿真器

Spectrum Digital XDS200 是最新 XDS200 系列 TI 处理器调试探针（仿真器）的首个模型。XDS200 系列拥有超低成本 XDS100 与高性能 XDS560v2 之间的低成本与高性能的完美平衡。此外，对于带有嵌入式缓冲跟踪器 (ETB) 的所有 ARM 和 DSP 处理器，所有 XDS 调试探针均支持内核和系统跟踪。

Spectrum Digital XDS200 通过 TI 20 引脚连接器（带有适合 TI 14 引脚、TI 10 引脚和 ARM 20 引脚的多个适配器）连接到目标板，而通过 USB2.0 高速连接 (480Mbps) 连接到主机 PC。要在主机 (...)

TMDSEMU560V2STM-U — Blackhawk XDS560v2 系统跟踪 USB 仿真器

XDS560v2 System Trace 是 XDS560v2 系列高性能 TI 处理器调试探针（仿真器）的第一种型号。XDS560v2 是 XDS 系列调试探针中性能最高的一款，同时支持传统 JTAG 标准 (IEEE1149.1) 和 cJTAG (IEEE1149.7)。

XDS560v2 System Trace 在其巨大的外部存储器缓冲区中加入了系统引脚跟踪。这种外部存储器缓冲区适用于指定的 TI 器件，通过捕获相关器件级信息，获得准确的总线性能活动和吞吐量，并对内核和外设进行电源管理。此外，对于带有嵌入式缓冲跟踪器 (ETB) 的所有 ARM 和 DSP 处理器，所有 XDS (...)

TMDSEMU560V2STM-UE — Spectrum Digital XDS560v2 系统跟踪 USB 和以太网

XDS560v2 System Trace 是 XDS560v2 系列高性能 TI 处理器调试探针（仿真器）的第一种型号。XDS560v2 是 XDS 系列调试探针中性能最高的一款，同时支持传统 JTAG 标准 (IEEE1149.1) 和 cJTAG (IEEE1149.7)。

XDS560v2 System Trace 在其巨大的外部存储器缓冲区中加入了系统引脚跟踪。这种外部存储器缓冲区适用于指定的 TI 器件，通过捕获相关器件级信息，获得准确的总线性能活动和吞吐量，并对内核和外设进行电源管理。此外，对于带有嵌入式缓冲跟踪器 (ETB) 的所有 ARM 和 DSP 处理器，所有 XDS (...)

FAXLIB — 用于 C66x、C64x+ 和 C55x 处理器的传真库 (FAXLIB)

处理器 SDK（软件开发套件）是统一的软件平台，适用于 TI 嵌入式处理器，设置简单，提供开箱即用的基准测试和演示。处理器 SDK 的所有版本在 TI 的广泛产品系列中保持一致，让开发人员可以无缝地在多种器件之间重用和迁移软件。处理器 SDK 和 TI 的嵌入式处理器解决方案让可扩展平台解决方案的开发变得前所未有地简单。

适用于 C6747、C6745 和 C6743 的处理器 SDK 包括 TI-RTOS 操作系统的各种支持。

RTOS 亮点：

• TI-RTOS 内核，一种用于 TI 器件的轻量级实时嵌入式操作系统
• 芯片支持库、驱动程序和基本的板级支持实用程序
• 经过优化的 C674x 算法库

SPRC264 — TMS320C6000 图像库 (IMGLIB)

C5000/6000 Image Processing Library (IMGLIB) is an optimized image/video processing function library for C programmers. It includes C-callable general-purpose image/video processing routines that are typically used in computationally intensive real-time applications. With these routines, higher (...)

SPRC265 — TMS320C6000 DSP 库 (DSPLIB)

TMS320C6000 Digital Signal Processor Library (DSPLIB) is a platform-optimized DSP function library for C programmers. It includes C-callable, general-purpose signal-processing routines that are typically used in computationally intensive real-time applications. With these routines, higher (...)

ADT-3P-DSPVOIPCODECS — 自适应数字技术 DSP VOIP、语音和音频编解码器

Adaptive Digital 是音质增强算法的开发公司，提供可与 TI DSP 配合使用的一流声学回声消除软件。Adaptive Digital 在算法开发、实施、优化和配置调优方面具有丰富的经验。他们提供适用于语音技术、音质软件、回声消除、会议软件、语音压缩算法的解决方案和即用型解决方案。

如需了解有关 Adaptive Digital 的更多信息，请访问 https://www.adaptivedigital.com。 发件人： Adaptive Digital Technologies, Inc.

VOCAL-3P-DSPVOIPCODECS — Vocal Technologies DSP VoIP 编解码器

经过 25 年以上的组装和 C 代码开发，VOCAL 的模块化软件套件可用于各种各样的 TI DSP 产品。产品具体包括 ATA、VoIP 服务器和网关、基于 HPNA 的 IPBX、视频监控、语音和视频会议、语音和数据射频器件、RoIP 网关、政务安全器件、合法拦截软件、医疗设备、嵌入式调制解调器、T.38 传真和 FoIP。

如需了解有关 Vocal Technologies 的更多信息，请访问 https://www.vocal.com。 发件人： VOCAL Technologies, Ltd.

C6745 PTP BSDL Model (Rev. C)

TI has partnered with companies to offer a wide range of software, tools, and SOMs using TI processors to accelerate your path to production. Download this search tool to quickly browse our third-party solutions and find the right third-party to meet your needs. The software, tools and modules (...)

TMS320C6745 PTP Allegro Footprint (Rev. A)

适用于 TI - C6745/6747 处理器的低成本集成电源解决方案