The TMS320C54x, TMS320LC54x, and TMS320VC54x fixed-point, digital signal processor (DSP) families (hereafter referred to as the ’54x unless otherwise specified) are based on an advanced modified Harvard architecture that has one program memory bus and three data memory buses. These processors also provide an arithmetic logic unit (ALU) that has a high degree of parallelism, application-specific hardware logic, on-chip memory, and additional on-chip peripherals. These DSP families also provide a highly specialized instruction set, which is the basis of the operational flexibility and speed of these DSPs.

Separate program and data spaces allow simultaneous access to program instructions and data, providing the high degree of parallelism. Two reads and one write operation can be performed in a single cycle. Instructions with parallel store and application-specific instructions can fully utilize this architecture. In addition, data can be transferred between data and program spaces. Such parallelism supports a powerful set of arithmetic, logic, and bit-manipulation operations that can all be performed in a single machine cycle. In addition, the ’C54x, ’LC54x, and ’VC54x versions include the control mechanisms to manage interrupts, repeated operations, and function calls.

• Advanced Multibus Architecture With Three Separate 16-Bit Data Memory Buses and One Program Memory Bus
• 40-Bit Arithmetic Logic Unit (ALU) Including a 40-Bit Barrel Shifter and Two Independent 40-Bit Accumulators
• 17- × 17-Bit Parallel Multiplier Coupled to a 40-Bit Dedicated Adder for Non-Pipelined Single-Cycle Multiply/Accumulate (MAC) Operation
• Compare, Select, and Store Unit (CSSU) for the Add/Compare Selection of the Viterbi Operator
• Exponent Encoder to Compute an Exponent Value of a 40-Bit Accumulator Value in a Single Cycle
• Two Address Generators With Eight Auxiliary Registers and Two Auxiliary Register Arithmetic Units (ARAUs)
• Data Bus With a Bus Holder Feature
• Address Bus With a Bus Holder Feature (’548 and ’549 Only)
• Extended Addressing Mode for 8M × 16-Bit Maximum Addressable External Program Space (’548 and ’549 Only)
• 192K × 16-Bit Maximum Addressable Memory Space (64K Words Program, 64K Words Data, and 64K Words I/O)
• On-Chip ROM with Some Configurable to Program/Data Memory
• Dual-Access On-Chip RAM
• Single-Access On-Chip RAM (’548/’549)
• Single-Instruction Repeat and Block-Repeat Operations for Program Code
• Block-Memory-Move Instructions for Better Program and Data Management
• Instructions With a 32-Bit Long Word Operand
• Instructions With Two- or Three-Operand Reads
• Arithmetic Instructions With Parallel Store and Parallel Load
• Conditional Store Instructions
• Fast Return From Interrupt
• On-Chip Peripherals
  • Software-Programmable Wait-State Generator and Programmable Bank Switching
  • On-Chip Phase-Locked Loop (PLL) Clock Generator With Internal Oscillator or External Clock Source
  • Full-Duplex Serial Port to Support 8- or 16-Bit Transfers (’541, ’LC545, and ’LC546 Only)
  • Time-Division Multiplexed (TDM) Serial Port (’542, ’543, ’548, and ’549 Only)
  • Buffered Serial Port (BSP) (’542, ’543, ’LC545, ’LC546, ’548, and ’549 Only)
  • 8-Bit Parallel Host-Port Interface (HPI) (’542, ’LC545, ’548, and ’549)
  • One 16-Bit Timer
  • External-Input/Output (XIO) Off Control to Disable the External Data Bus, Address Bus and Control Signals
• Power Consumption Control With IDLE1, IDLE2, and IDLE3 Instructions With Power-Down Modes
• CLKOUT Off Control to Disable CLKOUT
• On-Chip Scan-Based Emulation Logic, IEEE Std 1149.1 (JTAG) Boundary Scan Logic
• 25-ns Single-Cycle Fixed-Point Instruction Execution Time [40 MIPS] for 5-V Power Supply (’C541 and ’C542 Only)
• 20-ns and 25-ns Single-Cycle Fixed-Point Instruction Execution Time (50 MIPS and 40 MIPS) for 3.3-V PowerSupply (’LC54x)
• 15-ns Single-Cycle Fixed-Point Instruction Execution Time (66 MIPS) for 3.3-V Power Supply (’LC54xA, ’548, ’LC549)
• 12.5-ns Single-Cycle Fixed-Point Instruction Execution Time (80 MIPS) for 3.3-V Power Supply (’LC548, ’LC549)
• 10-ns and 8.3-ns Single-Cycle Fixed-Point Instruction Execution Time (100 and 120 MIPS) for 3.3-V Power Supply (2.5-V Core) (’VC549)

IEEE Standard 1149.1-1990 Standard-Test-Access Port and Boundary Scan Architecture.

• DSP
• 1 C54x
• DSP MHz (Max)
• 50
• CPU
• 16-bit
• Rating
• Catalog

TMS320LC543的完整型号有：TMS320LC543PZ1-40、TMS320LC543PZ1-50，以下是这些产品的关键参数及官网采购报价：

TMS320LC543PZ1-40，工作温度：PropertyValue，封装：LQFP (PZ)-100，包装数量MPQ：90个，MSL 等级/回流焊峰值温度：Level-1-260C-UNLIM，引脚镀层/焊球材料：NIPDAU，TI官网TMS320LC543PZ1-40的批量USD价格：24.99（1000+）

TMS320LC543PZ1-50，工作温度：PropertyValue，封装：LQFP (PZ)-100，包装数量MPQ：90个，MSL 等级/回流焊峰值温度：Level-1-260C-UNLIM，引脚镀层/焊球材料：NIPDAU，TI官网TMS320LC543PZ1-50的批量USD价格：27.489（1000+）

TMDSDSK5416 — TMS320C5416 DSP 入门套件 (DSK)

TMS320C5416 DSP 入门套件 (DSK) 是一个低成本开发平台，旨在加快基于 TI TMS320C54x DSP 的节能型应用的开发速度。该套件提供 USB 通信和真正的即插即用功能等性能增强型新功能，可让初级和熟练的设计人员立刻轻松地开始着手创新产品设计。

C5416 DSK 可以检测、诊断和校正 DSK 通信问题，更快地下载和逐步浏览代码，并利用实时数据交换 (RTDX?) 获得更高的吞吐量。

套件的所有内容包括：

• C5416 DSP 开发板 -
• C5416 DSK Code Composer Studio?v2.1 IDE
• 快速入门指南
• 技术参考资料
• (...)

PROCESSORS-3P-SEARCH — Arm-based MPU, arm-based MCU and DSP third-party search tool

TI has partnered with companies to offer a wide range of software, tools, and SOMs using TI processors to accelerate your path to production. Download this search tool to quickly browse our third-party solutions and find the right third-party to meet your needs. The software, tools and modules (...)