The TPA2001D1 is a 1-W mono bridge-tied-load (BTL) class-D amplifier designed to drive a speaker with at least 8- impedance. The amplifier uses TI’s third generation modulation technique, which results in improved efficiency and SNR. It also allows the device to be connected directly to the speaker without the use of the LC output filter commonly associated with class-D amplifiers (this results in EMI which must be shielded at the system level). These features make the device ideal for use in devices where high-efficiency is needed to extend battery run time.

The gain of the amplifier is controlled by two input terminals, GAIN1, and GAIN0. This allows the amplifier to be configured for a gain of 6, 12, 18, and 23.5 dB. The differential input terminals are high-impedance CMOS inputs, and can be used as summing nodes.

The class-D BTL amplifier includes depop circuitry to reduce the amount of turnon pop at power up, and when cycling SHUTDOWN\.

The TPA2001D1 is available in the 16-pin TSSOP package that drives 1 W of continuous output power into an 8- load. TPA2001D1 operates over an ambient temperature range of –40°C to 85°C.

• Modulation Scheme Optimized to Operate Without a Filter
• TSSOP Package Options
• 1 W Into an 8- Speaker (THD+N<1%)
• <0.2% THD+N at 1 W, 1 kHz, Into an 8- Load
• Extremely Efficient Third Generation 5-V Class-D Technology:
  • Low-Supply Current (No Filter) ...4 mA
  • Low-Supply Current (Filter) . . . 7.5 mA
  • Low-Shutdown Current . . . 0.05 μA
  • Low-Noise Floor ...40 μVRMS (No-Weighting Filter)
  • Maximum Efficiency Into 8 , 75 – 85%
  • 4 Internal Gain Settings ...6 – 23.5 dB
  • PSRR . . . –77 dB
• Integrated Depop Circuitry
• Short-Circuit Protection (Short to Battery, Ground, and Load)

• Audio input type
• Analog Input
• Architecture
• Class-D
• Speaker channels (Max)
• Mono
• Power stage supply (Max) (V)
• 5.5
• Power stage supply (Min) (V)
• 2.5
• Load (Min) (ohms)
• 8
• Output power (W)
• 1
• SNR (dB)
• 95
• THD + N @ 1 kHz (%)
• 0.1
• Iq (Typ) (mA)
• 4
• Control interface
• GPIO
• Closed/open loop
• Closed
• Analog supply (Min) (V)
• 2.5
• Analog supply (Max) (V)
• 5.5
• PSRR (dB)
• 72
• Operating temperature range (C)
• -40 to 85

TPA2001D1的完整型号有：TPA2001D1PW、TPA2001D1PWR，以下是这些产品的关键参数及官网采购报价：

TPA2001D1PW，工作温度：-40 to 85，封装：TSSOP (PW)-16，包装数量MPQ：90个，MSL 等级/回流焊峰值温度：Level-1-260C-UNLIM，引脚镀层/焊球材料：NIPDAU，TI官网TPA2001D1PW的批量USD价格：1.022（1000+）

TPA2001D1PWR，工作温度：-40 to 85，封装：TSSOP (PW)-16，包装数量MPQ：2000个，MSL 等级/回流焊峰值温度：Level-1-260C-UNLIM，引脚镀层/焊球材料：NIPDAU，TI官网TPA2001D1PWR的批量USD价格：.851（1000+）

TPA2001D1EVM — TPA2001D1 评估模块 (EVM)

The TPA2001D1 is a 1-W mono bridge-tied-load (BTL) Class-D amplifier designed to drive a speaker with at least 8 Ohms impedance. The amplifier uses TI's third generation modulation technique, which results in improved efficiency and SNR. It also allows the device to be connected directly to the (...)

PSPICE-FOR-TI — 适用于 TI 设计和模拟工具的 PSpice

PSpice for TI 可提供帮助评估模拟电路功能的设计和仿真环境。此功能齐全的设计和仿真套件使用 Cadence 的模拟分析引擎。PSpice for TI 可免费使用，包括业内超大的模型库之一，涵盖我们的模拟和电源产品系列以及精选的模拟行为模型。

借助?PSpice for TI 的设计和仿真环境及其内置的模型库，您可对复杂的混合信号设计进行仿真。创建完整的终端设备设计和原型解决方案，然后再进行布局和制造，可缩短产品上市时间并降低开发成本。

在?PSpice for TI 设计和仿真工具中，您可以搜索 TI (...)