The TPD12S015 device is an integrated HDMI ESD solution. The device pin mapping matches the HDMI Type C and Type D connector with four differential pairs. This device offers eight low-capacitance ESD clamps, allowing HDMI 1.3 or 1.4 data rates. The integrated ESD clamps and resistors provide good matching between each differential signal pair, which allows an advantage over discrete ESD clamp solutions where variations between ESD clamps degrade the differential signal quality.

The TPD12S015 provides a regulated 5-V output (5VOUT) for sourcing the HDMI power line. The regulated 5-V output supplies up to 55 mA to the HDMI receiver. The control of 5VOUT and the hot plug detect (HPD) circuitry is independent of the LS_OE control signal and is controlled by the CT_CP_HPD pin. This independent control enables the detection scheme (5VOUT + HPD) to be active before enabling the HDMI link.

There are three noninverting, bidirectional translation circuits for the SDA, SCL, and CEC lines. Each have a common power rail (V_CCA) on the A side from 1.1 V to 3.6 V . On the B side, the SCL_B and SDA_B each have an internal 1.75-kΩ pullup connected to the regulated 5-V rail (5VOUT). The SCL and SDA pins meet the I²C specification and drive up to 750-pF loads. The CEC_B pin has an internal 27-kΩ pullup to an internal 3.3-V supply.

The HPD_B port has a glitch filter to avoid false detection due to the bouncing while inserting the HDMI plug.

The TPD12S015 provides IEC61000-4-2 (Level 4) ESD protection. This device is offered in a space-saving 1.6-mm × 2.8-mm wafer-level chip scale package [DSBGA (YFF)] with a 0.4-mm pitch.

• HDMI 1.3 and HDMI 1.4 Data Rate
• HDMI High-Speed Differential Signals –3-dB Bandwidth Exceeds 6.4 Gbps
• Excellent Matching Capacitance (0.05 pF) in Each Differential Signal Pair
• Internal Boost Converter to Generate 5 V From a 2.3-V to 5.5-V Battery Voltage
• HDMI Minimum Current Limit and Short-Circuit Protection at 5VOUT Pin
• Flexible Power-Saving Modes Through Separate Control Pins
• Auto-Direction Sensing Level Shifting in the CEC, SDA, and SCL Lines Drive up to 750-pF Load
• Seamless Type C and Type D Connector Routing With Flow-Through Pin Mapping
• IEC 61000-4-2 (Level 4) System Level ESD Compliance
• Integrated IOFF and Backdrive Current Protection
• Space-Saving 1.6-mm × 2.8-mm DSBGA (YFF) Package

• Protocols
• HDMI
• Supply voltage (V)
• 2.3, 5.5
• Operating temperature range (C)
• -40 to 85

TPD12S015的完整型号有：TPD12S015YFFR，以下是这些产品的关键参数及官网采购报价：

TPD12S015YFFR，工作温度：-40 to 85，封装：DSBGA (YFF)-28，包装数量MPQ：3000个，MSL 等级/回流焊峰值温度：Level-1-260C-UNLIM，引脚镀层/焊球材料：SNAGCU，TI官网TPD12S015YFFR的批量USD价格：0.668（1000+）

TPD12S015AEVM — TPD12S015A 评估模块

The TPD12S015A is an integrated HDMI companion chip solution. The device pin mapping matches the HDMI Type D or Type C connector with four differential pairs. This device offers 8 low capacitance ESD clamps allowing HDMI 1.4 data rates. The integrated ESD clamps and resistors provide good matching (...)

TPD12S016PWREVM — TPD12S016PWR 评估模块

TPD12S016 是单芯片 HDMI 接口设备，具有自动方向感应的 I2C 电压电平转换缓冲器、负载开关和集成高速 ESD 保护钳位。器件引脚映射通过四个差动对与 HDMI D 类连接器匹配。该器件提供了 8 个低电容 ESD 钳位，支持 HDMI 1.4 数据速率。集成的 ESD 电路可在各个差动信号对之间实现良好的匹配，这更优于分立 ESD 解决方案，原因在于 ESD 保护钳位之间的变量降低了差动信号的质量。TPD12S016 以 5V 电流限制输出 (5V_OUT) 为 HDMI 电力线供电。5V 电流限制输出为 HDMI 接收器供应高达 55 mA 的电流。5V (...)

PSPICE-FOR-TI — 适用于 TI 设计和模拟工具的 PSpice

PSpice for TI 可提供帮助评估模拟电路功能的设计和仿真环境。此功能齐全的设计和仿真套件使用 Cadence 的模拟分析引擎。PSpice for TI 可免费使用，包括业内超大的模型库之一，涵盖我们的模拟和电源产品系列以及精选的模拟行为模型。

借助?PSpice for TI 的设计和仿真环境及其内置的模型库，您可对复杂的混合信号设计进行仿真。创建完整的终端设备设计和原型解决方案，然后再进行布局和制造，可缩短产品上市时间并降低开发成本。

在?PSpice for TI 设计和仿真工具中，您可以搜索 TI (...)

TINA-TI — 基于 SPICE 的模拟仿真程序

TINA-TI 提供了 SPICE 所有的传统直流、瞬态和频域分析以及更多。TINA 具有广泛的后处理功能，允许您按照希望的方式设置结果的格式。虚拟仪器允许您选择输入波形、探针电路节点电压和波形。TINA 的原理图捕获非常直观 - 真正的“快速入门”。

TINA-TI 安装需要大约 500MB。直接安装，如果想卸载也很容易。我们相信您肯定会爱不释手。

TINA 是德州仪器 (TI) 专有的 DesignSoft 产品。该免费版本具有完整的功能，但不支持完整版 TINA 所提供的某些其他功能。

如需获取可用 TINA-TI 模型的完整列表，请参阅：SpiceRack - 完整列表

需要 HSpice (...)