The TPIC2810 device is a monolithic, medium-voltage, low-current, 8-bit shift register design to drive low-side switched resistive loads such as LEDs. The device is not recommended for switching inductive loads.

This device contains an 8-bit, serial-in, parallel-out shift register that feeds an 8-bit D-type storage register. Data transfers through the shift register via an I²C bus interface. Data is transferred into the data shift register only after the group ID and device address have been verified. The subaddress directs the I²C bus interface to read or write data to the device or transfer data to the output. When output enable (G)\ is held high, all drain outputs are off. When G\ is held low, data from the output storage register is transparent to the output buffers. When data in the output buffers is low, the DMOS transistor outputs are off. When data is high, the DMOS transistor outputs have sink-current capability.

The TPIC2810 device has an internal power-up clear to initialize all registers to an off state when power is applied to the device. It also has a thermal sensor to monitor the die temperature and shut the drain outputs off, if an over current condition occurs.

Outputs are low-side, open-drain DMOS transistors with output ratings of 40 V and 100 mA continuous sink-current capability. Each output provides a 210-mA maximum current limit at T_C = 25°C. The current limit decreases as the junction temperature increases for additional device protection. The device also provides up to 3000 V of ESD protection on output terminals and 2000 V of ESD protection on input terminals when tested using the human-body model.

The TPIC2810 device is characterized for operation over the operating case temperature range of –40°C to 125°C.

• Low rDS(on) ...5 Typical
• Eight Power DMOS Transistor Outputs of
• 100-mA Continuous Current
• 210-mA Current Limit Capability
• Drain Output ESD Protection . . . 3000 V
• Output Clamp Voltage . . . 40 V

• Number of channels (#)
• 8
• Topology
• Open drain
• Rating
• Automotive
• Operating temperature range (C)
• -40 to 125
• Vin (Min) (V)
• 3
• Vin (Max) (V)
• 5.5
• Vout (Max) (V)
• 40
• Features
• I2C Control

TPIC2810的完整型号有：TPIC2810D、TPIC2810DG4、TPIC2810DR、TPIC2810DRG4，以下是这些产品的关键参数及官网采购报价：

TPIC2810D，工作温度：-40 to 125，封装：SOIC (D)-16，包装数量MPQ：40个，MSL 等级/回流焊峰值温度：Level-1-260C-UNLIM，引脚镀层/焊球材料：NIPDAU，TI官网TPIC2810D的批量USD价格：.616（1000+）

TPIC2810DG4，工作温度：PropertyValue，封装：SOIC (D)-16，包装数量MPQ：40个，MSL 等级/回流焊峰值温度：Level-1-260C-UNLIM，引脚镀层/焊球材料：NIPDAU，TI官网TPIC2810DG4的批量USD价格：.693（1000+）

TPIC2810DR，工作温度：-40 to 125，封装：SOIC (D)-16，包装数量MPQ：2500个，MSL 等级/回流焊峰值温度：Level-1-260C-UNLIM，引脚镀层/焊球材料：NIPDAU，TI官网TPIC2810DR的批量USD价格：.513（1000+）

TPIC2810DRG4，工作温度：PropertyValue，封装：SOIC (D)-16，包装数量MPQ：2500个，MSL 等级/回流焊峰值温度：Level-1-260C-UNLIM，引脚镀层/焊球材料：NIPDAU，TI官网TPIC2810DRG4的批量USD价格：.59（1000+）

TMDX654GPEVM — AM65x 评估模块 (EVM)

The AM65x Evaluation Module provides a platform to quickly start evaluation of Sitara™ Arm® Cortex®-A53 AM65x Processors (AM6548,AM6546,AM6528,AM6527,AM6526) and accelerate development for HMI, networking, patient monitoring, and other industrial applications. It is a development platform based (...)

TMDX654HSEVM — AM65x 高安全性 (HS) 评估模块 (EVM)

AM65x 高安全性 (HS) 评估模块提供了平台，用于评估 Sitara™ Arm® Cortex®-A53 AM65x 处理器（AM6548、AM6546、AM6528、AM6527、AM6526）的安全引导和其他安全特性。它是基于四核 Cortex-A53、双 Cortex-R5F 处理器的开发平台，集成有 PCIe、USB 3.0/2.0、千兆以太网等各种连接选项。

TMDX654IDKEVM — AM65x 工业开发套件 (IDK)

AM65x 工业开发套件 (IDK) 是用于评估 Sitara™ AM65x 处理器工业通信和控制功能的开发平台，适用于工厂自动化、驱动器、机器人、电网基础设施等领域的应用。AM65x 处理器包含三个 PRU-ICSS（适用于工业通信的可编程实时单元）子系统，该子系统可用于 Profinet、EtherCAT、以太网/IP 等千兆工业以太网协议。

PSPICE-FOR-TI — 适用于 TI 设计和模拟工具的 PSpice

PSpice for TI 可提供帮助评估模拟电路功能的设计和仿真环境。此功能齐全的设计和仿真套件使用 Cadence 的模拟分析引擎。PSpice for TI 可免费使用，包括业内超大的模型库之一，涵盖我们的模拟和电源产品系列以及精选的模拟行为模型。

借助?PSpice for TI 的设计和仿真环境及其内置的模型库，您可对复杂的混合信号设计进行仿真。创建完整的终端设备设计和原型解决方案，然后再进行布局和制造，可缩短产品上市时间并降低开发成本。

在?PSpice for TI 设计和仿真工具中，您可以搜索 TI (...)