The power supply provides regulated 5-V output to power the system microcontroller and drive eight low-side switches. The AC zero-detect circuitry is monitoring the crossover voltage of the mains AC supply. The resultant signal is a low-frequency clock output on the ZVS terminal, based on the AC-line cycle. This information allows the microcontroller to reduce in-rush current by powering loads on the AC-line peak voltage.

A serial communications interface controls the eight low-side outputs; each output has an internal snubber circuit to absorb the energy in the inductor at turn OFF. Alternatively, the system can use a fly-back diode to V_IN to help recirculate the energy in an inductive load at turn OFF.

• Eight Low-Side Drivers With Internal Clamp for Inductive Loads and Current Limiting for Self Protection
  • Seven Outputs Rated at 150 mA and Controlled Through Serial Interface
  • One Output Rated at 150 mA and Controlled Through Serial Interface and Dedicated Enable Pin
• 5-V ±5% Regulated Power Supply With 200-mA Load Capability at VIN Max of 18 V
• Internal Voltage Supervisory for Regulated Output
• Serial Communications for Control of Eight Low-Side Drivers
• Enable/Disable Input for OUT1
• 5-V or 3.3-V I/O Tolerant for Interface to Microcontroller
• Programmable Power-On Reset Delay Before RST Asserted High, Once 5 V Is Within Specified Range (6 ms Typ)
• Programmable Deglitch Timer Before RST Is Asserted Low (40 μs Typ)
• Zero-Voltage Detection Signal
• Thermal Shutdown for Self Protection
• APPLICATIONS
  • Electrical Appliances
    • Air Conditioning Units
    • Ranges
    • Dishwashers
    • Refrigerators
    • Microwaves
    • Washing Machines
  • General-Purpose Interface Circuits, Allowing Microcontroller Interface to Relays, Electric Motors, LEDs, and Buzzers

PowerPAD is a trademark of Texas Instruments.

• Drivers per package
• 8
• Output voltage (Max) (V)
• 16.5
• Peak output current (mA)
• 150
• Delay time (Typ) (ns)
• 10, 80
• Input compatibility
• CMOS
• Vol @ lowest spec current (Typ) (mV)
• 400
• Iout/ch (Max) (mA)
• 150
• Iout_off (Typ) (uA)
• 2
• Rating
• Catalog

TPL9201的完整型号有：TPL9201PWP、TPL9201PWPR，以下是这些产品的关键参数及官网采购报价：

TPL9201PWP，工作温度：-40 to 125，封装：HTSSOP (PWP)-20，包装数量MPQ：70个，MSL 等级/回流焊峰值温度：Level-2-260C-1 YEAR，引脚镀层/焊球材料：NIPDAU，TI官网TPL9201PWP的批量USD价格：.62（1000+）

TPL9201PWPR，工作温度：-40 to 125，封装：HTSSOP (PWP)-20，包装数量MPQ：2000个，MSL 等级/回流焊峰值温度：Level-2-260C-1 YEAR，引脚镀层/焊球材料：NIPDAU，TI官网TPL9201PWPR的批量USD价格：.517（1000+）

PSPICE-FOR-TI — 适用于 TI 设计和模拟工具的 PSpice

PSpice for TI 可提供帮助评估模拟电路功能的设计和仿真环境。此功能齐全的设计和仿真套件使用 Cadence 的模拟分析引擎。PSpice for TI 可免费使用，包括业内超大的模型库之一，涵盖我们的模拟和电源产品系列以及精选的模拟行为模型。

借助?PSpice for TI 的设计和仿真环境及其内置的模型库，您可对复杂的混合信号设计进行仿真。创建完整的终端设备设计和原型解决方案，然后再进行布局和制造，可缩短产品上市时间并降低开发成本。

在?PSpice for TI 设计和仿真工具中，您可以搜索 TI (...)