The TPS40042 DC/DC controller is designed to operate with an input source between a 3.0 V and 5.5 V. To reduce the number of external components, a number of operating parameters are fixed internally. The operating frequency for example, is internally set at 600 kHz.

One of three short circuit threshold levels may be selected by the addition of an external resistor from the COMP pin to circuit ground (no resistor is the default setting). During power on, and before the internal soft start commands the output voltage to rise, the TPS40042 enters a calibration cycle, measures the current out of the COMP pin, and selects an internal SCP threshold voltage. At the end of the 1.5-ms calibration time, the output voltage is allowed to enter soft-start. During operation, the selected SCP threshold voltage is compared to the upper MOSFET’s voltage drop during its ON time to determine whether there is an overload condition. If the voltage across the MOSFET exceeds the threshold voltage, the TPS40042 counts seven continuous pulses before shutting completely OFF for seven soft start charge/discharge cycles, after which, the TPS40042 attempts to restart the output.

During startup, both the high-side MOSFET switch and the synchronous rectifier are held in the OFF state until the internal soft start commands an output voltage higher than the voltage currently at the output. This may happen when the output is pre-biased at some voltage greater than zero and less than the desired regulation voltage. When the internal soft start first commands the output to rise, the pulse width of the synchronous rectifier is slowly increased from zero to the full 1-D conduction time by a number of discrete steps. In this way, inductor current is not allowed to reverse quickly, and ensures a monotonic startup of the output whether the output starts from zero or from a pre-bias level. If power is applied to the device while the EN (enable low) pin is allowed to float high, the TPS40042 remains OFF. Only when the EN pin is pulled down towards ground is the controller allowed to start.

• 3.0-V to 5.5-V Input
• External Reference required: 0.5 V to 1.5 V
• Output Voltage from REFIN to 90% of VIN
• High-Side Drive for N-Channel FET
• Supports Pre-Biased Outputs
• Adaptive Anti-Cross Conduction Gate Drive
• Fixed switching frequency (600 kHz) Voltage Mode Control
• Three Selectable Short Circuit Protection Levels
• Hiccup Restart from Faults
• Active Low Enable
• Thermal Shutdown Protection at 145°C
• 10-Pin, 3-mm x 3-mm SON (DRC)
• APPLICATIONS
  • DDR Memory
  • Point of Load
  • Telecommunications
  • DC to DC Modules

Predictive Gate Drive Is a trademark of Texas Instruments.

• Vin (Min) (V)
• 3
• Vin (Max) (V)
• 5.5
• Vout (Min) (V)
• 0.6
• Vout (Max) (V)
• 4.95
• Iout (Max) (A)
• 6
• Iq (Typ) (uA)
• 1000
• Switching frequency (Min) (kHz)
• 600
• Switching frequency (Max) (kHz)
• 600
• Features
• Output Discharge
• Regulated outputs (#)
• 1
• Number of phases
• 1
• Rating
• Catalog

TPS40042的完整型号有：TPS40042DRCR、TPS40042DRCT，以下是这些产品的关键参数及官网采购报价：

TPS40042DRCR，工作温度：-40 to 85，封装：VSON (DRC)-10，包装数量MPQ：3000个，MSL 等级/回流焊峰值温度：Level-2-260C-1 YEAR，引脚镀层/焊球材料：NIPDAU，TI官网TPS40042DRCR的批量USD价格：.823（1000+）

TPS40042DRCT，工作温度：-40 to 85，封装：VSON (DRC)-10，包装数量MPQ：250个，MSL 等级/回流焊峰值温度：Level-2-260C-1 YEAR，引脚镀层/焊球材料：NIPDAU，TI官网TPS40042DRCT的批量USD价格：.988（1000+）

TPS40042 Unencrypted PSpice Transient Model Package (Rev. A)

PSpice for TI 可提供帮助评估模拟电路功能的设计和仿真环境。此功能齐全的设计和仿真套件使用 Cadence 的模拟分析引擎。PSpice for TI 可免费使用，包括业内超大的模型库之一，涵盖我们的模拟和电源产品系列以及精选的模拟行为模型。

借助?PSpice for TI 的设计和仿真环境及其内置的模型库，您可对复杂的混合信号设计进行仿真。创建完整的终端设备设计和原型解决方案，然后再进行布局和制造，可缩短产品上市时间并降低开发成本。

在?PSpice for TI 设计和仿真工具中，您可以搜索 TI (...)