The TPS6014x step-up, regulated charge pumps generate a 5-V ±4% output voltage from a 1.8-V to 3.6-V input voltage range. The devices are typically powered by two alkaline, NiCd, or NiMH battery cells and provide an output current of minimum 100 mA from a 2-V input. Only four external capacitors are needed to build a complete voltage tripler charge pump.

The devices regulate the output by using the pulse-skip topology. The controller is optimized for lowest output voltage ripple over the complete output current range. The output peak current and therefore the output voltage ripple are drastically reduced compared to a conventional pulse-skip topology by regulating the charge pump output resistance. At light loads the maximum output resistance is limited to assure a low quiescent current.

The TPS60140 includes a low-battery comparator that issues a warning if the battery voltage drops below a user-adjustable threshold voltage. The TPS60141 features a power-good output that goes active when the output voltage reaches 90% of its nominal value.

The logic shutdown function disables the converter, reduces the supply current to a maximum of 1 μA and disconnects the output from the input. Special current-control circuitry prevents excessive current from being drawn from the battery during start-up. This DC/DC converter requires no inductors, therefore, EMI is of little concern. The TPS6014x operates over a free-air temperature range of –40°C to 85°C. It is available in the small, thermally enhanced 20-pin HTSSOP package (PWP).

• Regulated 5 V ±4% Output Voltage
• Up to 100-mA Output Current
• 1.8-V to 3.6-V Input Voltage Range
• 65-μA Quiescent Supply Current
• 0.05-μA Shutdown Current, Battery Is Isolated From Load in Shutdown
• Integrated Low-Battery or Power-Good Indicator
• Low-Output Voltage Ripple Over Complete Output Current Range
• Easy-to-Design With Low-EMI Power Supply Because No Inductors Are Required
• Evaluation Module Available (TPS60140EVM-144)
• Available in a 6.5-mm × 4.4-mm 20-Pin HTSSOP Package

• Vin (Min) (V)
• 1.8
• Vin (Max) (V)
• 3.6
• Vout (Min) (V)
• 5
• Vout (Max) (V)
• 5
• Iout (Max) (A)
• 0.1
• Regulated outputs (#)
• 1
• Switching frequency (Min) (kHz)
• 210
• Switching frequency (Max) (kHz)
• 450
• Iq (Typ) (mA)
• 0.055
• Features
• Enable, Power Good
• Rating
• Catalog

TPS60141的完整型号有：TPS60141PWP、TPS60141PWPR，以下是这些产品的关键参数及官网采购报价：

TPS60141PWP，工作温度：-40 to 85，封装：HTSSOP (PWP)-20，包装数量MPQ：70个，MSL 等级/回流焊峰值温度：Level-2-260C-1 YEAR，引脚镀层/焊球材料：NIPDAU，TI官网TPS60141PWP的批量USD价格：.83（1000+）

TPS60141PWPR，工作温度：-40 to 85，封装：HTSSOP (PWP)-20，包装数量MPQ：2000个，MSL 等级/回流焊峰值温度：Level-2-260C-1 YEAR，引脚镀层/焊球材料：NIPDAU，TI官网TPS60141PWPR的批量USD价格：.692（1000+）

TPS60140EVM-144 — 2 节电池，5.0V，最小 100mA 三倍电压充电泵 EVM

The TPS60140EVM-144 is an evaluation tool for the regulated voltage tripler charge pump TPS60140. The package includes a tested evalutation module (EVM), an EVM user's guide (SLVU023) that contains the schematic, bill of material, components placement, layout and the setup of the EVM. The (...)

PSPICE-FOR-TI — 适用于 TI 设计和模拟工具的 PSpice

PSpice for TI 可提供帮助评估模拟电路功能的设计和仿真环境。此功能齐全的设计和仿真套件使用 Cadence 的模拟分析引擎。PSpice for TI 可免费使用，包括业内超大的模型库之一，涵盖我们的模拟和电源产品系列以及精选的模拟行为模型。

借助?PSpice for TI 的设计和仿真环境及其内置的模型库，您可对复杂的混合信号设计进行仿真。创建完整的终端设备设计和原型解决方案，然后再进行布局和制造，可缩短产品上市时间并降低开发成本。

在?PSpice for TI 设计和仿真工具中，您可以搜索 TI (...)

TIDA-010008 — 用于针对电网应用提供瞬态保护且基于平缓钳位 TVS 的参考设计

该参考设计采用多种方法，使用平缓钳位浪涌保护措施、ESD 器件、电子保险丝或负载开关，来保护交流或直流模拟输入、直流模拟输出、交流或直流二进制输入、带高侧或低侧驱动器的数字输出、LCD 偏置电源、USB 接口（电源和数据）和具有 24、12 或 5V 输入的板载电源（用于多个电网应用），使其免受过压、过载和瞬变（1.2/50us，42Ω）的影响。该设计监测温度、湿度、磁场和电源以进行诊断。