The TPS6021x step-up, regulated charge pumps generate a 3.3-V ±4% output voltage from a 1.8-V to 3.6-V input voltage. These devices are typically powered by two alkaline, NiCd, or NiMH battery cells or by one primary lithium MnO2 (or similar) coin cell and operate down to a minimum supply voltage of 1.6 V. Continuous output current is a minimum of 100 mA for the TPS60210 and TPS60211, and 50 mA for the TPS60212 and TPS60213, all from a 2-V input.

Three operating modes can be programmed using the SNOOZE\ pin. When SNOOZE\ is low, the device is put into snooze mode. In snooze mode, the device operates with a typical quiescent current of 2 uA while the output voltage is maintained at 3.3 V ±6%. This is lower than the self-discharge current of most batteries. Load current in snooze mode is limited to 2 mA. When SNOOZE\ is high, the device is put into normal operating mode. During normal operating mode, the device operates in the newly developed linskip mode where it switches seamlessly from the power saving pulse-skip mode at light loads to the low-noise constant-frequency linear-regulation mode once the output current exceeds the linskip current threshold of about 7 mA. In this mode, the device operates from the internal oscillator. The device is synchronized to an external clock signal if SNOOZE\ is clocked; thus switching harmonics can be controlled and minimized.

Only four external capacitors are needed to build a complete low-ripple dc/dc converter. The push-pull operating mode of two single-ended charge pumps assures the low output voltage ripple as charge is continuously transferred to the output. All the devices can start with full load current. The devices include a low-battery detector that issues a warning if the battery voltage drops below a user-defined threshold voltage or a power-good detector that goes active when the output voltage reaches about 90% of its nominal value. This dc/dc converter requires no inductors; therefore, EMI of the system is reduced to a minimum, making it easier to use in designs. It is available in the small 10-pin MSOP package (DGS).

• Regulated 3.3-V Output Voltage From a 1.8-V to 3.6-V Input Voltage Range
• UltraLow Operating Current in Snooze Mode, Typical 2 uA With up to 2-mA Output Current
• Less Than 5-mV(PP) Output Voltage Ripple Achieved With Push-Pull Topology
• Integrated Low-Battery and Power-Good Detector
• Switching Frequency Can Be Synchronized to External Clock Signal
• Extends Battery Usage With up to 90% Efficiency and 35-uA Quiescent Current
• Easy-To-Design, Low Cost, Low EMI Power Supply Since No Inductors Are Used
• Compact Converter Solution in UltraSmall 10-Pin MSOP With Only Four External Capacitors Required
• Evaluation Module Available (TPS60210EVM-167)
• Applications
  • Replaces DC/DC Converters With Inductors in Battery-Powered Applications Like:
    • Two Battery Cells to 3.3-V Conversion
    • MSP430 Ultralow-Power Microcontroller and Other Battery Powered Microprocessor Systems
    • Glucose Meters and Other Medical Instruments
    • MP3 Portable Audio Players
    • Backup-Battery Boost Converters
    • Cordless Phones, PDAs

• Vin (Min) (V)
• 1.8
• Vin (Max) (V)
• 3.6
• Vout (Min) (V)
• 3.3
• Vout (Max) (V)
• 3.3
• Iout (Max) (A)
• 0.05
• Regulated outputs (#)
• 1
• Switching frequency (Min) (kHz)
• 200
• Switching frequency (Max) (kHz)
• 400
• Iq (Typ) (mA)
• 0.002
• Features
• Frequency Synchronization
• Rating
• Catalog

TPS60212的完整型号有：HPA00210DGSR、TPS60212DGS、TPS60212DGSR，以下是这些产品的关键参数及官网采购报价：

HPA00210DGSR，工作温度：-40 to 85，封装：VSSOP (DGS)-10，包装数量MPQ：2500个，MSL 等级/回流焊峰值温度：-，引脚镀层/焊球材料：-，TI官网HPA00210DGSR的批量USD价格：.629（1000+）

TPS60212DGS，工作温度：-40 to 85，封装：VSSOP (DGS)-10，包装数量MPQ：80个，MSL 等级/回流焊峰值温度：Level-1-260C-UNLIM，引脚镀层/焊球材料：NIPDAU，TI官网TPS60212DGS的批量USD价格：.755（1000+）

TPS60212DGSR，工作温度：-40 to 85，封装：VSSOP (DGS)-10，包装数量MPQ：2500个，MSL 等级/回流焊峰值温度：Level-1-260C-UNLIM，引脚镀层/焊球材料：NIPDAU，TI官网TPS60212DGSR的批量USD价格：.629（1000+）

PSPICE-FOR-TI — 适用于 TI 设计和模拟工具的 PSpice

PSpice for TI 可提供帮助评估模拟电路功能的设计和仿真环境。此功能齐全的设计和仿真套件使用 Cadence 的模拟分析引擎。PSpice for TI 可免费使用，包括业内超大的模型库之一，涵盖我们的模拟和电源产品系列以及精选的模拟行为模型。

借助?PSpice for TI 的设计和仿真环境及其内置的模型库，您可对复杂的混合信号设计进行仿真。创建完整的终端设备设计和原型解决方案，然后再进行布局和制造，可缩短产品上市时间并降低开发成本。

在?PSpice for TI 设计和仿真工具中，您可以搜索 TI (...)