The TPS6030x devices are a family of switched-voltage converters designed specifically for space-critical battery powered applications.

The TPS6030x step-up, regulated charge pumps generate a 3-V (±4%) or 3.3-V (±4%) output voltage from a 0.9-V to 1.8-V input voltage (one alkaline, NiCd, or NiMH battery).

Only five small 1-µF ceramic capacitors are required to build a complete high efficiency DC-DC charge pump converter. To achieve the high efficiency over a wide input voltage range, the charge pump automatically selects between a 3× or 4× conversion mode.

Output 1 (OUT1) can deliver a maximum of 40 mA from a 1-V input, with output 2 (OUT2) not loaded. OUT2 can deliver a maximum of 20 mA from a 1-V input, with OUT1 not loaded. Both outputs can be loaded at the same time, but the total output current of the first voltage doubler must not exceed 40 mA. For example, the load at output 1 is 20 mA and the load at output 2 is 10 mA.

The devices operate in the newly developed LinSkip mode. In this operating mode, the device switches seamlessly from the power saving, pulse-skip mode at light loads, to the low-noise, constant-frequency linear-regulation mode, when the output current exceeds the device-specific output current threshold.

A power-good function supervises the output voltage of OUT2 and can be used for power-up and power-down sequencing. Power good (PG) is offered as either open-drain or push-pull output.

• Input Voltage Range From 0.9 V to 1.8 V
• Regulated 3-V or 3.3-V Output Voltage
• Up to 20-mA Output Current
• High Power Conversion Efficiency (up to 90%) Over a Wide Output Current Range, Optimized for 1.2-V Battery Voltage
• Additional Output With 2 Times VIN (OUT1)
• Device Quiescent Current Less Than 35 μA
• Supervisor Included; Open Drain or Push-Pull Power Good Output
• Minimum Number of External Components
  • No Inductors Required
  • Only Five Small, 1-μF Ceramic Capacitors Required
• Load Isolated From Battery During Shutdown
• Micro-Small 10-Pin MSOP (VSSOP) Package

All trademarks are the property of their respective owners.

• Vin (Min) (V)
• 0.9
• Vin (Max) (V)
• 1.8
• Vout (Min) (V)
• 3.3
• Vout (Max) (V)
• 3.3
• Iout (Max) (A)
• 0.04
• Regulated outputs (#)
• 2
• Switching frequency (Min) (kHz)
• 470
• Switching frequency (Max) (kHz)
• 650
• Iq (Typ) (mA)
• 0.035
• Features
• Enable, Power Good
• Rating
• Catalog

TPS60300的完整型号有：TPS60300DGS、TPS60300DGSR，以下是这些产品的关键参数及官网采购报价：

TPS60300DGS，工作温度：-40 to 85，封装：VSSOP (DGS)-10，包装数量MPQ：80个，MSL 等级/回流焊峰值温度：Level-1-260C-UNLIM，引脚镀层/焊球材料：NIPDAU，TI官网TPS60300DGS的批量USD价格：.895（1000+）

TPS60300DGSR，工作温度：-40 to 85，封装：VSSOP (DGS)-10，包装数量MPQ：2500个，MSL 等级/回流焊峰值温度：Level-1-260C-UNLIM，引脚镀层/焊球材料：NIPDAU，TI官网TPS60300DGSR的批量USD价格：.746（1000+）

PSPICE-FOR-TI — 适用于 TI 设计和模拟工具的 PSpice

PSpice for TI 可提供帮助评估模拟电路功能的设计和仿真环境。此功能齐全的设计和仿真套件使用 Cadence 的模拟分析引擎。PSpice for TI 可免费使用，包括业内超大的模型库之一，涵盖我们的模拟和电源产品系列以及精选的模拟行为模型。

借助?PSpice for TI 的设计和仿真环境及其内置的模型库，您可对复杂的混合信号设计进行仿真。创建完整的终端设备设计和原型解决方案，然后再进行布局和制造，可缩短产品上市时间并降低开发成本。

在?PSpice for TI 设计和仿真工具中，您可以搜索 TI (...)

TIDM-RF-SENSORNODE — 用于 6LoWPAN 和 2.4 GHz 应用的 RF 传感器节点开发平台

射频传感器节点平台旨在用作 6LoWPAN 和 2.4 GHz 应用的微型开发平台。此平台有三种板载传感器，其中包括一个 3 轴加速器、一个温度传感器和两个光传感器。射频传感器节点平台可作为独立传感器节点，也可与 PLC（电力线通信）板或射频接口板配对形成混合节点。射频节点支持 2.4GHz 射频协议，其中包括 6LoWPAN 或 ZigBee。由于节点之间的链路可以是有线和/或无线的，因此混合网络可以提供比传统节点更优的可靠性和抗噪声能力。