The TPS6031X step-up, regulated charge pumps generate a 3-V ±4% or 3.3-V ±4% output voltage from a 0.9-V to 1.8-V input voltage (one alkaline, NiCd, or NiMH battery).

Only five small 1-uF ceramic capacitors are required to build a complete high-efficiency dc/dc charge pump converter. To achieve the high efficiency over a wide input voltage range, the charge pump automatically selects between a 3x or 4x conversion mode.

Output 1 (OUT1) can deliver a maximum of 40 mA, from a 1-V input, with output 2 (OUT2) not loaded. OUT2 can deliver a maximum of 20 mA, from a 1-V input, with OUT1 not loaded. Both outputs can be loaded at the same time, but the total output current of the first voltage doubler must not exceed 40 mA. For example, the load at OUT1 is 20 mA and the load at output 2 is 10 mA.

In snooze mode, the devices operate with a typical operating current of 2 uA, while the output voltage is maintained at 3.3 V ±10% or 3 V ±10%, respectively. This is lower than the self-discharge current of most batteries. Load current in snooze mode is limited to 2 mA. If the load current increases above 2 mA, the output voltage drops further and the devices automatically exits the snooze mode and operate in normal mode to regulate to the nominal output voltage with higher output currents. The device is set into the snooze mode by taking the SNOOZE\ pin low, and is set into normal operating mode by taking the SNOOZE\ pin high.

A power-good function supervises the output voltage of OUT2 and can be used for power up and power down sequencing. Power-good (PG) is offered as either open-drain or push-pull output.

• Regulated 3-V or 3.3-V Output Voltage With up to 20-mA Output Current From a 0.9-V to 1.8-V Input Voltage Range
• High Power Conversion Efficiency (up to 90%) Over Wide Output Current Range, Optimized for 1.2-V Battery Voltage
• Snooze Mode for Improved Efficiency at Low-Output Current
• Additional Output With 2 Times VI (OUT1)
• Device Quiescent Current Less Than 2 uA
• Supervisor Included; Open Drain or Push-Pull Power Good Output
• No Inductors Required/Low EMI
• Only Five Small, 1-uF Ceramic Capacitors Required
• Microsmall 10-Pin MSOP Package
• applications
  • Pagers
  • Battery-Powered Toys
  • Portable Measurement Instruments
  • Home Automation Products
  • Medical Instruments (Like Hearing Instruments)
  • Metering Applications Using MSP430 Microcontroller
  • Portable Smart Card Readers

• Vin (Min) (V)
• 0.9
• Vin (Max) (V)
• 1.8
• Vout (Min) (V)
• 3
• Vout (Max) (V)
• 3
• Iout (Max) (A)
• 0.02
• Regulated outputs (#)
• 1
• Switching frequency (Min) (kHz)
• 470
• Switching frequency (Max) (kHz)
• 900
• Iq (Typ) (mA)
• 0.002
• Features
• Power Good
• Rating
• Catalog

TPS60311的完整型号有：TPS60311DGS、TPS60311DGSR，以下是这些产品的关键参数及官网采购报价：

TPS60311DGS，工作温度：-40 to 85，封装：VSSOP (DGS)-10，包装数量MPQ：80个，MSL 等级/回流焊峰值温度：Level-1-260C-UNLIM，引脚镀层/焊球材料：NIPDAU，TI官网TPS60311DGS的批量USD价格：.83（1000+）

TPS60311DGSR，工作温度：-40 to 85，封装：VSSOP (DGS)-10，包装数量MPQ：2500个，MSL 等级/回流焊峰值温度：Level-1-260C-UNLIM，引脚镀层/焊球材料：NIPDAU，TI官网TPS60311DGSR的批量USD价格：.692（1000+）

PSPICE-FOR-TI — 适用于 TI 设计和模拟工具的 PSpice

PSpice for TI 可提供帮助评估模拟电路功能的设计和仿真环境。此功能齐全的设计和仿真套件使用 Cadence 的模拟分析引擎。PSpice for TI 可免费使用，包括业内超大的模型库之一，涵盖我们的模拟和电源产品系列以及精选的模拟行为模型。

借助?PSpice for TI 的设计和仿真环境及其内置的模型库，您可对复杂的混合信号设计进行仿真。创建完整的终端设备设计和原型解决方案，然后再进行布局和制造，可缩短产品上市时间并降低开发成本。

在?PSpice for TI 设计和仿真工具中，您可以搜索 TI (...)