The TPS6100x devices are boost converters intended for systems that are typically operated from a single- or dual-cell nickel-cadmium (NiCd), nickel-metal hydride (NiMH), or alkaline battery. The converter output voltage can be adjusted from 1.5 V to a maximum of 3.3 V and provides a minimum output current of 100 mA from a single battery cell and 250 mA from two battery cells. The converter starts up into a full load with a supply voltage of 0.9 V and stays in operation with supply voltages as low as 0.8 V.

The converter is based on a fixed-frequency, current-mode pulse-width-modulation (PWM) controller that goes into power-save mode at low load currents. The current through the switch is limited to a maximum of 1100 mA, depending on the output voltage. The current sense is integrated to further minimize external component count. The converter can be disabled to minimize battery drain when the system is put into standby.

A low-EMI mode is implemented to reduce interference and radiated electromagnetic energy that is caused by the ringing of the inductor when the inductor discharge-current decreases to zero. The device is packaged in the space-saving 10-pin MSOP package.

• Start-Up Into a Full Load With Supply Voltages as Low as 0.9 V Over Full Temperature Range
• Minimum 100-mA Output Current From 0.8-V Supply Voltage, 250 mA From 1.8 V
• High Power Conversion Efficiency, up to 90%
• Power-Save Mode for Improved Efficiency at Low Output Currents
• Device Quiescent Current Less Than 50 μA
• Added System Security With Integrated Low- Battery Comparator
• Low-EMI Converter (Integrated Antiringing Switch Across Inductor)
• Micro-Size 10-Pin MSOP Package
• Evaluation Modules Available (TPS6100xEVM–156)

• Vin (Min) (V)
• 0.8
• Vin (Max) (V)
• 3.3
• Vout (Min) (V)
• 3.3
• Vout (Max) (V)
• 3.3
• Switch current limit (Typ) (A)
• 1.1
• Regulated outputs (#)
• 1
• Switching frequency (Min) (kHz)
• 360
• Switching frequency (Max) (kHz)
• 840
• Iq (Typ) (mA)
• 0.05
• Features
• Enable, Light Load Efficiency, Power Good
• Duty cycle (Max) (%)
• 100
• Rating
• Catalog

TPS61006的完整型号有：TPS61006DGS、TPS61006DGSR，以下是这些产品的关键参数及官网采购报价：

TPS61006DGS，工作温度：-40 to 85，封装：VSSOP (DGS)-10，包装数量MPQ：80个，MSL 等级/回流焊峰值温度：Level-1-260C-UNLIM，引脚镀层/焊球材料：NIPDAU，TI官网TPS61006DGS的批量USD价格：1.348（1000+）

TPS61006DGSR，工作温度：-40 to 85，封装：VSSOP (DGS)-10，包装数量MPQ：2500个，MSL 等级/回流焊峰值温度：Level-1-260C-UNLIM，引脚镀层/焊球材料：NIPDAU，TI官网TPS61006DGSR的批量USD价格：1.141（1000+）

TPS61006 TINA-TI Transient Reference Design

PSpice for TI 可提供帮助评估模拟电路功能的设计和仿真环境。此功能齐全的设计和仿真套件使用 Cadence 的模拟分析引擎。PSpice for TI 可免费使用，包括业内超大的模型库之一，涵盖我们的模拟和电源产品系列以及精选的模拟行为模型。

借助?PSpice for TI 的设计和仿真环境及其内置的模型库，您可对复杂的混合信号设计进行仿真。创建完整的终端设备设计和原型解决方案，然后再进行布局和制造，可缩短产品上市时间并降低开发成本。

在?PSpice for TI 设计和仿真工具中，您可以搜索 TI (...)