The TPS6103x devices provide a power supply solution for products powered by either a one-cell Li-Ion or Li-polymer, or a two to three-cell alkaline, NiCd or NiMH battery. The converter generates a stable output voltage that is either adjusted by an external resistor divider or fixed internally on the chip. It provides high efficient power conversion and is capable of delivering output currents up to 1 A at 5 V at a supply voltage down to 1.8 V. The implemented boost converter is based on a fixed frequency, pulse-width- modulation (PWM) controller using a synchronous rectifier to obtain maximum efficiency. At low load currents the converter enters Power Save mode to maintain a high efficiency over a wide load current range. The Power Save mode can be disabled, forcing the converter to operate at a fixed switching frequency. It can also operate synchronized to an external clock signal that is applied to the SYNC pin. The maximum peak current in the boost switch is limited to a value of 4500 mA.

The converter can be disabled to minimize battery drain. During shutdown, the load is completely disconnected from the battery. A low-EMI mode is implemented to reduce ringing and, in effect, lower radiated electromagnetic energy when the converter enters the discontinuous conduction mode.

• 96% Efficient Synchronous Boost Converter With 1000-mA Output Current From 1.8-V Input
• Device Quiescent Current: 20-μA (Typ)
• Input Voltage Range: 1.8-V to 5.5-V
• Fixed and Adjustable Output Voltage Options Up to 5.5-V
• Power Save Mode for Improved Efficiency at Low Output Power
• Low Battery Comparator
• Low EMI-Converter (Integrated Antiringing Switch)
• Load Disconnect During Shutdown
• Over-Temperature Protection
• Available in a Small 4 mm × 4 mm QFN-16 or in a TSSOP-16 Package

• Vin (Min) (V)
• 1.8
• Vin (Max) (V)
• 5.5
• Vout (Min) (V)
• 1.8
• Vout (Max) (V)
• 5.5
• Switch current limit (Typ) (A)
• 4
• Regulated outputs (#)
• 1
• Switching frequency (Min) (kHz)
• 500
• Switching frequency (Max) (kHz)
• 700
• Iq (Typ) (mA)
• 0.02
• Features
• Synchronous Rectification
• Duty cycle (Max) (%)
• 100
• Rating
• Catalog

TPS61030的完整型号有：TPS61030PWP、TPS61030PWPR、TPS61030RSAR，以下是这些产品的关键参数及官网采购报价：

TPS61030PWP，工作温度：-40 to 85，封装：HTSSOP (PWP)-16，包装数量MPQ：90个，MSL 等级/回流焊峰值温度：Level-2-260C-1 YEAR，引脚镀层/焊球材料：NIPDAU，TI官网TPS61030PWP的批量USD价格：1.336（1000+）

TPS61030PWPR，工作温度：-40 to 85，封装：HTSSOP (PWP)-16，包装数量MPQ：2000个，MSL 等级/回流焊峰值温度：Level-2-260C-1 YEAR，引脚镀层/焊球材料：NIPDAU，TI官网TPS61030PWPR的批量USD价格：1.113（1000+）

TPS61030RSAR，工作温度：-40 to 85，封装：QFN (RSA)-16，包装数量MPQ：3000个，MSL 等级/回流焊峰值温度：Level-2-260C-1 YEAR，引脚镀层/焊球材料：NIPDAU，TI官网TPS61030RSAR的批量USD价格：1.113（1000+）

TPS61030EVM-029 — TPS61030 评估模块（QFN 封装）

The TPS61030EVM-029 is an evaluation tool for the TPS61030 inductive step-up converter in QFN-16 package which can supply voltages up to 5.5V from a 1.8-V to 5.5-V input. The TPS61030EVM-029 uses a TPS61030 adjustable output step-up converter and the appropriate external components to provide a 5-V (...)

TPS61030EVM-208 — TPS61030 评估模块

The TPS61030EVM-208 is an evaluation tool for the TPS61030 inductive boost converter in a TSSOP-16 package that can supply voltages up to 5.5 V from input voltages in the range of 1.8 V to 5.5 V. The EVM is configured to supply an output voltage of 5 V at up to 1000 mA. The EVM can also be used to (...)

TPS61031EVM-208 — TPS61031 评估模块

The TPS61031EVM-208 is an evaluation tool for the TPS61031 inductive boost converter in a TSSOP-16 package that can supply an output voltage of 3.3 V at up to 1000 mA from input voltages in the range of 1.8 V to 5.5 V.

TPS61032EVM-208 — TPS61032 评估模块

The TPS61032EVM-208 is an evaluation tool for the TPS61032 inductive boost converter in a TSSOP-16 package that can supply an output voltage of 5V at up to 1000 mA from input voltages in the range of 1.8V to 5.5V.

TPS61030 Unencrypted PSpice Transient Model Package (Rev. A)

PSpice for TI 可提供帮助评估模拟电路功能的设计和仿真环境。此功能齐全的设计和仿真套件使用 Cadence 的模拟分析引擎。PSpice for TI 可免费使用，包括业内超大的模型库之一，涵盖我们的模拟和电源产品系列以及精选的模拟行为模型。

借助?PSpice for TI 的设计和仿真环境及其内置的模型库，您可对复杂的混合信号设计进行仿真。创建完整的终端设备设计和原型解决方案，然后再进行布局和制造，可缩短产品上市时间并降低开发成本。

在?PSpice for TI 设计和仿真工具中，您可以搜索 TI (...)

TPS6103xVM Gerber Files

此电源管理解决方案通过各类电池为智能流量计量应用（居民燃气表和水表）提供 900mA@3.6V 电流。TIDA-00676 包括一个适用于 wM-Bus @ 169 MHz 的支持 ETSI 1 类接收器的射频子系统，提供高达 +30 dBm 发射功率，可满足意大利和法国 169MHz 射频链路的所有技术要求。电源管理和射频子系统均可应用于数据收集器和采用 wM-Bus@ 169 MHz 链路的其他终端节点（电表或家用能源显示设备）。

PMP9755 — 超级电容器与 TPS61030 结合使用并用于数据集中器电路的备用电源解决方案参考设计

此参考设计使用具有 TPS61030 升压转换器的超级电容器提供备用电源电路。如果低功率系统在系统出现故障时需要备用切换电路，超级电容器连同 TPS61030 可在整个系统完全关闭之前提供充分电力来保持数据通信。