The TPS6112x devices provide a complete power supply solution for products powered by either a one-cell Li-Ion or Li-Polymer by either a one-cell Li-Ion or Li-Polymer battery, or a two- to four-cell Alkaline, NiCd, or NiMH battery. The devices can generate two stable output voltages that are either adjusted by an external resistor divider or are fixed internally on the chip. The device also provides a simple solution for generating 3.3 V out of a one-cell Li-Ion or Li-Polymer battery at a maximum output current of at least 200 mA with supply voltages down to 1.8 V. The implemented boost converter is based on a fixed frequency, pulse-width-modulation (PWM) controller using a synchronous rectifier to obtain maximum efficiency. The maximum peak current in the boost switch is limited to a value of 1600 mA.

The converter can be disabled to minimize battery drain. During shutdown, the load is completely disconnected from the battery. A low-EMI mode is implemented to reduce ringing and, in effect, lower radiated electromagnetic energy when the converter enters discontinuous conduction mode. A power good output at the boost stage simplifies control of any connected circuits like cascaded power supply stages or microprocessors.

The built-in LDO can be used for a second output voltage derived either from the boost output or directly from the battery. The LDO can be enabled separately that is, using the power good of the boost stage. The device is packaged in a 16-pin VQFN (RSA) package measuring 4 mm × 4 mm or in a 16-pin TSSOP (PW) package.

• Synchronous, 95% Efficient, Boost Converter With 500-mA Output Current From 1.8-V Input
• Integrated 200-mA Reverse Voltage Protected LDO for DC-DC Output Voltage Post Regulation or Second Output Voltage
• 40-μA (Typical) Total Device Quiescent Current
• Input Voltage Range: 1.8 V to 5.5 V
• Fixed and Adjustable Output Voltage Options up to 5.5 V
• Power Save Mode for Improved Efficiency at Low Output Power
• Low Battery Comparator
• Power Good Output
• Low EMI-Converter (Integrated Antiringing Switch)
• Load Disconnect During Shutdown
• Overtemperature Protection
• Available in a Small 4-mm × 4-mm VQFN-16 or in a TSSOP-16 Package

• Vin (Min) (V)
• 1.8
• Vin (Max) (V)
• 5.5
• Vout (Min) (V)
• 2.5
• Vout (Max) (V)
• 5.5
• Switch current limit (Typ) (A)
• 1.6
• Regulated outputs (#)
• 2
• Switching frequency (Min) (kHz)
• 400
• Switching frequency (Max) (kHz)
• 600
• Iq (Typ) (mA)
• 0.04
• Features
• Enable, Light Load Efficiency, Load Disconnect, Power Good
• Duty cycle (Max) (%)
• 100
• Rating
• Catalog

TPS61120的完整型号有：TPS61120PW、TPS61120PWR、TPS61120RSAR，以下是这些产品的关键参数及官网采购报价：

TPS61120PW，工作温度：-40 to 85，封装：TSSOP (PW)-16，包装数量MPQ：90个，MSL 等级/回流焊峰值温度：Level-1-260C-UNLIM，引脚镀层/焊球材料：NIPDAU，TI官网TPS61120PW的批量USD价格：1.534（1000+）

TPS61120PWR，工作温度：-40 to 85，封装：TSSOP (PW)-16，包装数量MPQ：2000个，MSL 等级/回流焊峰值温度：Level-1-260C-UNLIM，引脚镀层/焊球材料：NIPDAU，TI官网TPS61120PWR的批量USD价格：1.278（1000+）

TPS61120RSAR，工作温度：-40 to 85，封装：QFN (RSA)-16，包装数量MPQ：3000个，MSL 等级/回流焊峰值温度：Level-2-260C-1 YEAR，引脚镀层/焊球材料：NIPDAU，TI官网TPS61120RSAR的批量USD价格：1.278（1000+）

TPS61120EVM-205 — TPS61120 评估模块

The TPS61120EVM-205 is an evaluation tool for the TPS61120 inductive boost converter with LDO in 4x4mm2 QFN. The boost stage can supply voltages up to 5.5V from input voltages in the range of 1.8V to 5.5V. The LDO stage can supply voltages down to 0.9V from input voltages in the range of 1.5V to (...)

PSPICE-FOR-TI — 适用于 TI 设计和模拟工具的 PSpice

PSpice for TI 可提供帮助评估模拟电路功能的设计和仿真环境。此功能齐全的设计和仿真套件使用 Cadence 的模拟分析引擎。PSpice for TI 可免费使用，包括业内超大的模型库之一，涵盖我们的模拟和电源产品系列以及精选的模拟行为模型。

借助?PSpice for TI 的设计和仿真环境及其内置的模型库，您可对复杂的混合信号设计进行仿真。创建完整的终端设备设计和原型解决方案，然后再进行布局和制造，可缩短产品上市时间并降低开发成本。

在?PSpice for TI 设计和仿真工具中，您可以搜索 TI (...)