The TPS61166 is a boost converter with a 20-V rated integrated switch FET and power diode that drives up to 5 LEDs in series. This device integrates a high side switch FET that can turn on/off the LED current within 1-µs of the applied external PWM signal. The high side switch also provides input-to-output isolation during IC shutdown.

The default white LED current is set with the external sensor resistor R1, and the feedback voltage is regulated to 200-mV, as shown in the typical application circuit. The LED current can be adjusted using a pulse width modulation (PWM) signal through the PWM pin. The LED current is synchronized to the PWM signal. The device does not discharge the output ceramic capacitor during dimming, thus reducing audible noise when dimming.

Separating the IC input (VIN pin) and power stage input (VBAT pin) makes the device flexible enough to support single- or two-cell Li-ion battery applications. Other protection features include 1.1-A peak-to-peak over current protection (OCP), over voltage protection (OVP), over load protection (OLP), and thermal shutdown. The TPS61166 is available in a 2.5 mm × 2.5 mm SON package with thermal pad.

• IC Supply Range: 2.5-V to 6-V
• Power Stage Input Range: 4.5-V to 10-V
• Integrated 1.1-A / 20-V Internal Switch FET and Power Diode
• Drive up to 5 LEDs in Series
• Fast on/off LED Current Within 1-μs in Brightness Dimming
• Burst PWM Dimming Method With Frequency Range From 60-Hz to 40-kHz
• Built-in Soft Start-up
• Over Load Protection
• Over Voltage Protection
• 2.5 × 2.5 × 0.8 mm SON Package
• APPLICATIONS
  • Small Form Factor LCD Backlight
  • Mobile Phone
  • Digital Camera
  • Personal Camcorder
  • Single Lens Reflex

• Number of channels (#)
• 1
• Vin (Min) (V)
• 2.5
• Vin (Max) (V)
• 10
• Vout (Min) (V)
• 2.5
• Vout (Max) (V)
• 17
• Type
• Inductive
• Switching frequency (Max) (kHz)
• 1400
• LED current per channel (mA)
• 400
• Peak efficiency (%)
• 85
• Topology
• Boost
• Features
• EasyScale 1-Wire Interface, OVP
• Operating temperature range (C)
• -40 to 85

TPS61166的完整型号有：TPS61166DSKR、TPS61166DSKT，以下是这些产品的关键参数及官网采购报价：

TPS61166DSKR，工作温度：-40 to 85，封装：SON (DSK)-10，包装数量MPQ：3000个，MSL 等级/回流焊峰值温度：Level-1-260C-UNLIM，引脚镀层/焊球材料：NIPDAU，TI官网TPS61166DSKR的批量USD价格：0.785（1000+）

TPS61166DSKT，工作温度：-40 to 85，封装：SON (DSK)-10，包装数量MPQ：250个，MSL 等级/回流焊峰值温度：Level-1-260C-UNLIM，引脚镀层/焊球材料：NIPDAU，TI官网TPS61166DSKT的批量USD价格：0.942（1000+）

PSPICE-FOR-TI — 适用于 TI 设计和模拟工具的 PSpice

PSpice for TI 可提供帮助评估模拟电路功能的设计和仿真环境。此功能齐全的设计和仿真套件使用 Cadence 的模拟分析引擎。PSpice for TI 可免费使用，包括业内超大的模型库之一，涵盖我们的模拟和电源产品系列以及精选的模拟行为模型。

借助?PSpice for TI 的设计和仿真环境及其内置的模型库，您可对复杂的混合信号设计进行仿真。创建完整的终端设备设计和原型解决方案，然后再进行布局和制造，可缩短产品上市时间并降低开发成本。

在?PSpice for TI 设计和仿真工具中，您可以搜索 TI (...)