The TPS704xx family of devices consists of dual-output, low-dropout voltage regulators with integrated SVS (RESET, POR, or power on reset) and power good (PG) functions. These devices are capable of supplying 1 A and 2 A by regulator 1 and regulator 2 respectively. Quiescent current is typically 185 µA at full load. Differentiated features, such as accuracy, fast transient response, SVS supervisory circuit (power on reset), manual reset input, and independent enable functions provide a complete system solution.

The TPS704xx family of voltage regulators offers very low dropout voltage and dual outputs. These devices have extremely low noise output performance without using any added filter bypass capacitors and are designed to have a fast transient response and be stable with 47-µF low ESR capacitors.

These devices have fixed 3.3-V/2.5-V, 3.3-V/1.8-V, 3.3-V/1.5-V, 3.3-V/1.2-V, and adjustable voltage options. Regulator 1 can support up to 1 A, and regulator 2 can support up to 2 A. Separate voltage inputs allow the designer to configure the source power.

Because the PMOS device behaves as a low-value resistor, the dropout voltage is very low (typically 160 mV on regulator 1) and is directly proportional to the output current. Additionally, since the PMOS pass element is a voltage-driven device, the quiescent current is very low and independent of output loading (maximum of 250 µA over the full range of output current and full range of temperature). This LDO family also features a sleep mode; applying a high signal to EN1 or EN2 (enable) shuts down regulator 1 or regulator 2, respectively. When a high signal is applied to both EN1 and EN2, both regulators enter sleep mode, thereby reducing the input current to 2 µA at T_J = +25°C.

For each regulator, there is an internal discharge transistor to discharge the output capacitor when the regulator is turned off (disabled).

The PG1 pin reports the voltage condition at V_OUT1. The PG1 pin can be used to implement a SVS (RESET, POR, or power on reset) for the circuitry supplied by regulator 1. The PG2 pin reports the voltage conditions at V_OUT2. The PG2 pin can be used to implement a SVS (power on reset) for the circuitry supplied by regulator 2.

The TPS704xx features a RESET (SVS, POR, or power on reset). RESET is an active low, open drain output and requires a pull-up resistor for normal operation. When pulled up, RESET goes into a high impedance state (that is, logic high) after a 120-ms delay when both of the following conditions are met. First, V_IN1 must be above the undervoltage condition. Second, the manual reset (MR) pin must be in a high impedance state. To monitor V_OUT1, the PG1 output pin can be connected to MR. To monitor V_OUT2, the PG2 output pin can be connected to MR. RESET can be used to drive power on reset or a low-battery indicator. If RESET is not used, it can be left floating.

Internal bias voltages are powered by V_IN1 and require 2.7 V for full functionality. Each regulator input has an undervoltage lockout circuit that prevents each output from turning on until the respective input reaches 2.5 V.

• Dual Output Voltages for Split-Supply Applications
• Independent Enable Functions (See Part Number TPS703xx for Sequenced Outputs)
• Output Current Range of 1 A on Regulator 1 and 2 A on Regulator 2
• Fast Transient Response
• Voltage Options: 3.3-V/2.5-V, 3.3-V/1.8-V, 3.3-V/1.5-V, 3.3-V/1.2-V, and Dual Adjustable Outputs
• Open Drain Power-On Reset with 120-ms Delay
• Open Drain Power Good for Regulator 1 and Regulator 2
• Ultralow 185μA (typ) Quiescent Current
• 2μA Input Current During Standby
• Low Noise: 78μVRMS Without Bypass Capacitor
• Quick Output Capacitor Discharge Feature
• One Manual Reset Input
• 2% Accuracy Over Load and Temperature
• Undervoltage Lockout (UVLO) Feature
• 24-Pin PowerPAD? TSSOP Package
• Thermal Shutdown Protection

PowerPAD is a trademark of Texas Instruments. All other trademarks are the property of their respective owners.

• Output options
• Adjustable Output, Dual Output, Fixed Output
• Iout (Max) (A)
• 1
• Vin (Max) (V)
• 6
• Vin (Min) (V)
• 2.7
• Vout (Max) (V)
• 5.5
• Vout (Min) (V)
• 1.2
• Fixed output options (V)
• 1.2, 1.5, 1.8, 2.5, 3.3
• Noise (uVrms)
• 78
• Iq (Typ) (mA)
• 0.185
• Thermal resistance θJA (°C/W)
• 32
• Rating
• Catalog
• Load capacitance (Min) (μF)
• 22
• Regulated outputs (#)
• 2
• Features
• Enable, Output discharge, Power good
• Accuracy (%)
• 2
• PSRR @ 100 KHz (dB)
• 22
• Dropout voltage (Vdo) (Typ) (mV)
• 160
• Operating temperature range (C)
• -40 to 125

TPS704的完整型号有：TPS70402PWP、TPS70402PWPR、TPS70445PWP、TPS70445PWPR、TPS70448PWP、TPS70448PWPR、TPS70451PWP、TPS70451PWPR、TPS70458PWP、TPS70458PWPR，以下是这些产品的关键参数及官网采购报价：

TPS70402PWP，工作温度：-40 to 125，封装：HTSSOP (PWP)-24，包装数量MPQ：60个，MSL 等级/回流焊峰值温度：Level-2-260C-1 YEAR，引脚镀层/焊球材料：NIPDAU，TI官网TPS70402PWP的批量USD价格：3.102（1000+）

TPS70402PWPR，工作温度：-40 to 125，封装：HTSSOP (PWP)-24，包装数量MPQ：2000个，MSL 等级/回流焊峰值温度：Level-2-260C-1 YEAR，引脚镀层/焊球材料：NIPDAU，TI官网TPS70402PWPR的批量USD价格：2.585（1000+）

TPS70445PWP，工作温度：-40 to 125，封装：HTSSOP (PWP)-24，包装数量MPQ：60个，MSL 等级/回流焊峰值温度：Level-2-260C-1 YEAR，引脚镀层/焊球材料：NIPDAU，TI官网TPS70445PWP的批量USD价格：3.102（1000+）

TPS70445PWPR，工作温度：-40 to 125，封装：HTSSOP (PWP)-24，包装数量MPQ：2000个，MSL 等级/回流焊峰值温度：Level-2-260C-1 YEAR，引脚镀层/焊球材料：NIPDAU，TI官网TPS70445PWPR的批量USD价格：2.585（1000+）

TPS70448PWP，工作温度：-40 to 125，封装：HTSSOP (PWP)-24，包装数量MPQ：60个，MSL 等级/回流焊峰值温度：Level-2-260C-1 YEAR，引脚镀层/焊球材料：NIPDAU，TI官网TPS70448PWP的批量USD价格：3.102（1000+）

TPS70448PWPR，工作温度：-40 to 125，封装：HTSSOP (PWP)-24，包装数量MPQ：2000个，MSL 等级/回流焊峰值温度：Level-2-260C-1 YEAR，引脚镀层/焊球材料：NIPDAU，TI官网TPS70448PWPR的批量USD价格：2.585（1000+）

TPS70451PWP，工作温度：-40 to 125，封装：HTSSOP (PWP)-24，包装数量MPQ：60个，MSL 等级/回流焊峰值温度：Level-2-260C-1 YEAR，引脚镀层/焊球材料：NIPDAU，TI官网TPS70451PWP的批量USD价格：3.102（1000+）

TPS70451PWPR，工作温度：-40 to 125，封装：HTSSOP (PWP)-24，包装数量MPQ：2000个，MSL 等级/回流焊峰值温度：Level-2-260C-1 YEAR，引脚镀层/焊球材料：NIPDAU，TI官网TPS70451PWPR的批量USD价格：2.585（1000+）

TPS70458PWP，工作温度：-40 to 125，封装：HTSSOP (PWP)-24，包装数量MPQ：60个，MSL 等级/回流焊峰值温度：Level-2-260C-1 YEAR，引脚镀层/焊球材料：NIPDAU，TI官网TPS70458PWP的批量USD价格：3.102（1000+）

TPS70458PWPR，工作温度：-40 to 125，封装：HTSSOP (PWP)-24，包装数量MPQ：2000个，MSL 等级/回流焊峰值温度：Level-2-260C-1 YEAR，引脚镀层/焊球材料：NIPDAU，TI官网TPS70458PWPR的批量USD价格：2.585（1000+）

AMC1300EVM — 具有高 CMTI 的 AMC1300 ±250mV 输入、增强型隔离放大器评估模块

The AMC1300 evaluation module (EVM)is a platform for evaluating the AMC1300, which is a 7-kV reinforced isolation amplifier designed for use in current shunt measuring applications.AMC1300EVM allows the user to explore all the features of the AMC1300 device.

AMC1302EVM — 适用于 AMC1302 ±50mV 输入、高精度、增强型隔离放大器的评估模块

AMC1302 评估模块 (EVM) 是用于评估 AMC1302 的平台，后者是一款旨在用于电流分流测量应用的 7kV 增强型隔离放大器。AMC1302EVM 可支持用户探索 AMC1302 器件的所有特性。

AMC1311EVM — AMC1311 评估模块

AMC1311 器件是一款高压隔离放大器，其差分输出与输入接口电路由二氧化硅 (SiO2) 隔离层隔开。隔离层提供高达 7000VPEAK 的电隔离。与 TLV6001 结合使用时，差分输出可转换为能够驱动各种模数转换器 (ADC) 的单端输出。

ISO224EVM — ISO224 评估模块

ISO224 评估模块 (EVM) 是 ISO224 的评估平台，后者是一款旨在用于电压测量应用的 7kV 增强型隔离放大器。ISO224EVM 可支持用户探索 ISO224 器件的所有特性。ISO224EVM 还具有双极和单极差分到单端输出级。